Bedienungsanleitung DRU Cosmo Tunnel (Seite 11 von 40) (Englisch)

810284

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

INSTALLATION MANUAL

5.8.3 Placing the concentric system

!Caution

• Maintain a distance of at least 50 mm between the outside of the concentric system and the walls and/or the

ceiling (see section 5.4). If the system is built in (for instance) a cove, it should be made with non combustible,

heat-resistant material all around it.

• Use heat-resistant insulation material when passing through combustible material.

• Create a terminal for the concentric system with the following diameters:

- The pipe diameter +25 mm for a passage through non combustible material (see Appendix 3, fig. 40).

- The pipe diameter +200 mm for a passage through combustible material. Insulate the surrounding free

space with at least 60 mm mineral wool (see Appendix 3, fig. 41).

• The rosette of the wall terminal is too small to seal the opening in case of passage through combustible

material. That is why a heat-resistant intermediate plate of sufficient size should first be mounted to the wall.

Then, the rosette is mounted on the intermediate sheet.

The roof terminal can end in a sloping and a flat roof.

The roof terminal can be supplied with an adhesive plate for a flat roof or with a universally adjustable tile for a

sloping roof.

!Caution

Some heat-resistant insulation materials contain volatile components that will spread an unpleasant smell for a

prolonged time; these are not suitable.

Place the concentric system as follows:

Build the system up from (the flue spigot of) the appliance.

Connect the concentric pipe pieces and, if necessary, the bend(s).

On each connection, apply a clip binding with silicon sealing ring.

Use a self-tapping screw to fix the clip binding to the pipe on locations that cannot be reached after installation.

Attach the concentric system with sufficient fastening brackets, so that the weight is not resting on the appliance.

Observe the following;

• Place the first fastening bracket 0.5 metre from the appliance, at the most.

• Place a fastening bracket maximum 0.1 metre from each bend, if the bends are more than 0.25 metre away

from each other. If two bends are closer to one another than 0.25 metre, 1 fastening bracket between these

bends will be sufficient.

• At least every 1 metre, place a fastening bracket at slanted and horizontal sections.

• At least every 2 metres, place a fastening bracket at vertical sections.

Fasten a roof terminal with anchor cables, if it protrudes more than 1,5 metres above the terminal.

Determine the remaining length for the wall or roof terminal and cut it to size, make sure the correct insertion

length is maintained.

Place the wall terminal with the (groove/folded) seam at the top.

Attach the wall terminal from the outside by means of four screws.

!Caution

When using the wall terminal, place the terminal with a downward slope of 1 cm / metre towards the outside, in

order to prevent rain water from raining in.

5.9 Connection to an existing chimney (C91)

The appliance can be connected to an existing chimney. A 100 mm diameter flexible SS pipe is placed in the

chimney for discharging flue gases. The surrounding space is used as combustion air supply.

In case of an appliance connection of ø200/130, 0.8 metres of concentric system must first be connected vertically.

Reduce the concentric system after the first 0.8 metres to a diameter of 150/100. The concentric system of 150/100

can be vertically connected to an existing chimney.

The following requirements apply when connecting to an existing chimney:

• Only allowed when used in combination with the special DRU chimney set. The installation regulation is parat

of the delivery.

• The internal size should be at least 150 x 150 mm.

• The vertical length has a maximum of 12 meters.

• The total horizontal pipe length may have a maximum length that can be found in appendix 2, table 4.

• The existing chimney should be clean.

• The existing chimney should be tight.

For setting the appliance, the same conditions/instructions apply as for the concentric system described above.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Cosmo Tunnel Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Cosmo Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info