Bedienungsanleitung DRU Diablo Next (Seite 13 von 36) (Englisch)

571631

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

English

INSTALLATION MANUAL

!Caution

Make sure the front glass pane makes full contact with the side pane (there may be no opening between the side

pane and front pane).

If the front and side glass panes do not connect:

Loosen the self-tapping screws and nuts of the side pane clamp strips by a few turns.

Slide the side pane tightly against the front pane.

!Caution

Make sure there is no sealing tape between the front and side panes (where the panes connect).

Tighten the self-tapping screws and nuts of the clamp strips.

5.11Settingtheappliance

The appliance has to be set in such a way that it works correctly with the used concentric system. For that purpose,

a restrictor slide is placed and/or an air inlet guide is removed. The conditions for application with wall terminal

and roof terminal are stated in appendix 2, tables 4, 5 and 6.

5.11.1Airinletguides

!Caution

There are no air inlet guides in the G31 appliance, so they do not have to be removed.

Check tables 4, 5 and 6 to see whether the restrictor slide has to be removed in your set-up.

The air inlet guides (L) are at the rear at the bottom of the combustion chamber of the appliance (see Appendix 3,

fig. 10 and 11).

Follow the procedure below when removing:

Remove the glass pane as described in section 5.10.1.

Remove the two self-tapping screws in the bottom of the combustion chamber (see Appendix 3, fig. 10).

Remove plate (M) as indicated (see Appendix 3, fig. 10).

Fully remove the four self-tapping screws of the two air inlet guides (see Appendix 3, fig. 11).

Remove the two air inlet guides (L).

Screw back the four self-tapping screws in the combustion chamber.

Place the plate (M) back in the combustion chamber.

Screw back the two self-tapping screws in the combustion chamber.

Place back the glass pane, as described in section 5.10.2.

!Caution

• All self-tapping screws must have been screwed back in the combustion chamber.

• Do not throw away the air inlet guides, you may need them in the future.

!Tip

If you are installing an appliance, whereby a restrictor slide has to be placed, do not yet place back the glass pane.

5.11.2Restrictorslide

The restrictor slide (R) must be adjusted to the right position (see Appendix 3, fig. 12).

Proceed as follows:

Remove the glass pane as described in section 5.10.1.

!Caution

The restrictor slide should be placed in the correct manner. Therefore, accurately observe the instructions in

Appendix 3, fig. 12.

Loosen the 2 self-tapping screws by a few turns, but not fully.

Adjust the position of the restrictor in accordance with tables 4, 5 and 6.

In the restrictor slide, 4 of the 5 possible positions are indicated by means of 4 cut out letters. B, C and

D correspond with the letters in table 5, the O is indicated in table 4.

Make sure that the point of the triangle belonging to the position that you want and the centre of the self-tapping

screw are exactly aligned.

!Caution

At restriction D, the restrictor slide should be placed fully towards the front.

Now tighten the 2 self-tapping screws.

At position A, the restrictor slide should be fully removed from the combustion chamber.

Proceed as follows:

Remove the 2 self-tapping screws of the restrictor slide from the combustion chamber (see appendix 3, fig. 12);

Remove the restrictor slide (R);

Screw back the self-tapping screws in the combustion chamber;

!Caution

• The self-tapping screws of the restrictor slide must have been screwed back in the combustion chamber.

• Do not throw away the restrictor slide, you may need it in the future.

Place back the glass pane, as described in section 5.10.2.

!Tip

If you are installing an appliance, whereby a wood set has to be placed, do not yet place back the glass pane.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU Diablo Next Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU Diablo Next

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info