Bedienungsanleitung DRU GLOBAL 100 BF (Seite 32 von 64) (Holländisch)

571711

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

INSTALLATION MANUAL

6.3 Gas connection

Place a gas tap in the gas connection, close to the appliance.

- Make sure there is no dirt in gas pipes and

connections;

- Prevent twisting the gas tap when con-

necting the gas pipe.

The following requirements apply to the gas connection:

- use a gas pipe with the correct dimensions, so that no

pressure loss can occur;

- the gas tap should have the CE marking;

- you should always be able to reach the gas tap.

6.4 Placing the appliance

- Make sure that combustible objects and/

or materials have a distance from the ap-

pliance of at least 500 mm;

- Always place the appliance against a wall of

non combustible and heat-resistant

material;

- Take sufﬁ cient measures to prevent tempe-

ratures of a wall behind the chimney breast

becoming too high, including the materials

and/or objects behind the wall;

- Do not make any changes to the appliance.

!Caution - Take the adjustable height of the appliance

into account; it depends on the setting of

the adjustable feet (see ﬁ g. 1);

- Take the minimum construction depth of

the appliance into account; Global 100 BF:

362 mm (see ﬁ g. 2);

- If required, install the Max vent system

prior to placing the appliance; see the

manual for the Max vent system;

- Take the different construction measure-

ments into account when applying the Max

vent system; see the manual for the Max

vent system.

!Tip You can determine the construction height

of the appliance (X in ﬁ g. 2) yourself.

Place the appliance as follows:

• Determine the location of the appliance.

• Determine the construction height of the appliance.

• Provide a gas connection at the location. For details,

see section 6.3.

• Make a passage for the ﬂ ue gas discharge/combustion air

supply system with the following diameters. For details,

see section 6.5.

- Ø160 mm for a wall terminal through non combustible

material;

- Ø 250 mm for a wall terminal through combustible

material;

- Ø160 mm for a roof terminal through non combustible

material;

- Ø 250 mm for a roof terminal through combustible mate-

rial.

• Place the appliance on its destined location.

The gas control is mounted under the appliance, at the bur-

ner plate. It should be disconnected and placed in the control

box at a later stage. For placing the gas control in the control

box, see section 6.7.

Follow the procedure described below:

• Disconnect the pipes from the gas control (ﬂ exible gas

pipe, aluminium pilot-ﬂ ame pipe and thermocouple 1).

!Caution The red wire of thermocouple 2 must

remain connected to the gas control.

• Disconnect the gas control from the burner plate by

unscrewing the self-tapping screw.

• Carefully unwind the red and black wires of

thermocouple 2.

• Lay the gas control together with the wires of

thermocouple 2 in the direction of the control box.

- Make sure there is no dirt in gas pipes and

connections;

- Avoid kinks in the pipes.

• Roll out the pipes in the direction of the control box.

• Roll out the ignition cable in the direction of the control

box.

!Caution - Make sure the ignition cable cannot come

into contact with other wires;

- The data plate should remain connected to

the chain.

• Place the chain with the data plate in the direction of the

control box.

• Set the height of the appliance using the adjustable feet and

• Make the appliance level at the same time.

- Do not place the appliance too tightly

against the back wall; this is guaranteed by

means of the spacer brackets;

- Make sure the space between the adjusta-

ble feet is kept free;

- Do not cover the appliance and/or do

not wrap it in an insulation blanket or any

other material.

6.5 Flue gas discharge / combustion air supply

system

6.5.1 General

The appliance is of the C11/C31 type.

The appliance is connected to a combined ﬂ ue gas

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 100 BF Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 100 BF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info