Bedienungsanleitung DRU GLOBAL 70 (Seite 47 von 60) (Englisch, Holländisch)

528137

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

English

USER MANUAL

Global 70 / 70 XT

Ignite the appliance as follows:

• Set button A on the gas control to ON (button B is

controlled automatically) (see ﬁ g. 4).

The gas control is located in the control box.

• Simultaneously press the buttons OFF and

(large ﬂ ame)

on the remote control.

• Let go of the buttons when a short sound signal indicates

that the ignition process has been started.

In succession:

- the continuous signals will indicate that the ignition

process is active;

- a short sound signal will indicate that the ignition process

has ﬁ nished;

- the appliance will automatically switch through to the

highest position of the main burner, which will start to

burn in a few seconds.

- If the pilot burner is not burning after

3 ignition attempts, you must close the

gas tap and call the installer;

- When igniting the pilot burner, you will

hear sound signals. After the last short

sound signal, the main burner should be

largely ignited within about 10 seconds.

If this is not the case, you must close the

gas tap and warn your installer;

- If the appliance ignites with a pop sound,

you must close the gas tap and contact

your installer.

!Tip A little motor will start to run when the

main burner operates, you will be able to

hear it.

4.2.2.2 Flame height / standby

The ﬂ ame height can be adjusted continuously by using the

buttons

(small ﬂ ame) and (large ﬂ ame). By continuing

to lower the ﬂ ame height, the appliance can be set to the

standby position; this means that only the pilot burner will

still be burning.

• Press button (small ﬂ ame) to lower the ﬂ ame height

and/or to set the appliance in the standby position.

• Press the button

(large ﬂ ame) to raise the ﬂ ame height

and/or to switch on the main burner from the standby

(pilot burner) position.

- If you continue to press down button

(large ﬂ ame) on the remote control, the

main burner should be largely ignited

within about 10 seconds. If this is not the

case, you must close the gas tap and warn

your installer;

- If the appliance ignites with a pop sound,

you must close the gas tap and contact

your installer.

4.2.2.3 Switching off

Switch the appliance off by pressing the OFF button.

The pilot burner will also go out.

4.2.3 Temperature display

The room temperature can be indicated on the display

in degrees Celsius (ºC) using a 24 hour clock or degrees

Fahrenheit (ºF) using a 12 hour clock.

• Simultaneously press OFF and

(small ﬂ ame), until the

correct display appears.

4.2.4 Time

The display can indicate time.

After placing the battery or simultaneously pressing

(large ﬂ ame) and (small ﬂ ame), the time indication will

ﬂ ash on the display and you will be able to adjust the time.

• Simultaneously press

and until the time indication

ﬂ ashes on the display.

• Press the button

(large ﬂ ame) to set the hours.

• Press the button (small ﬂ ame) to set the minutes.

• Press OFF to return to the MAN position, or wait for the

system to automatically return to the MAN position.

4.2.5 Thermostat function

Using the thermostat function you can set two temperatu-

res, which can be controlled thermostatically.

These temperatures are referred to as day temperature

and night temperature.

The ✹ TEMP and  TEMP symbols on the display refer to

day and night temperature respectively.

The room temperature is compared to the set day/night

temperature and then the ﬂ ame height is automatically

controlled in order to reach the set temperature.

To be able to use the day/night temperature function, the

appliance must be in the standby position.

!Caution - Always leave the remote control at the

same place, so that the thermostat is able

to ‘feel’ the room temperature;

- Make sure this place is free from inﬂ uen-

ces such as draught, heat from radiators

and direct sunlight.

Example

By using the ✹ TEMP function you can keep the day tempe-

rature at 20 ºC; while you use the  TEMP function at night

to maintain a temperature of 15 ºC.

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 70 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info