Bedienungsanleitung DRU GLOBAL 70 (Seite 48 von 60) (Englisch, Holländisch)

528137

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

USER MANUAL

4.2.5.1 Setting day/night temperature

By using the SET button, you will go through the following

functions:

MAN  ✹ TEMP   TEMP  (P*) TIMER  MAN

• Brieﬂ y press the SET button to enter the ✹ TEMP or the

TEMP position.

• Press the SET button until the temperature on the display

ﬂ ashes.

• Set the required temperature by using the buttons

(large ﬂ ame) and (small ﬂ ame).

!Caution - The minimum temperature you can set is

5 ºC / 40 ºF;

- Control of the night temperature is

switched off by lowering the temperature

until two stripes (“--”) appear on the

display.

• Press the OFF button or wait until position ✹ TEMP or

 TEMP appears on the display.

4.2.5.2 Activating the thermostat function

For activating the thermostat function, you must proceed

with the following steps:

• Place the appliance in the standby (pilot burner) position

using button

(small ﬂ ame).

• Set the day/night temperature.

• Choose the ✹ TEMP or  TEMP function using the SET

button.

4.2.6 Timer for thermostat function

Using the timer enables you to set two times per 24 hours

for switching on the day temperature and two times per 24

hours for switching on the night temperature.

In order to control the night temperature, it should be set

to at least 5 ºC / 40 oF.

If the night temperature is set to the “- - ” position, the

appliance will remain in the standby position. The appliance

will only switch on at the next switch-on time of the day

temperature.

The appliance must be in standby position in order to be

controlled by the timer.

Example of switch times

You have set a day temperature and night temperature of,

for example, 20 ºC and 15 ºC.

P1 ✹ TIMER = 7 hours; the temperature will go to 20 ºC

at 7 am.

P1  TIMER = 9 hours; the temperature will go to 15 ºC

at 9 am.

P2 ✹ TIMER = 17 hours; the temperature will go to 20 ºC

at 5 pm.

P2  TIMER = 22 hours; the temperature returns to 15 ºC

at 10 pm.

4.2.6.1 Setting times for the timer

To set the timer, proceed as follows:

• Set the day and night temperature as described above at

section 4.2.5.1.

• Brieﬂ y press the SET button to enter the (P*) TIMER

position.

• Press the SET button until P1 ✹ TIMER is displayed and

the time ﬂ ashes.

• Set the ﬁ rst switch on time of the day temperature using

the buttons

(large ﬂ ame) and (small ﬂ ame).

• Brieﬂ y press the SET button to set the next time of the

cycle, P1  TIMER.

• Successively set the times P2 ✹ TIMER and P2  TIMER.

• Press the OFF button or wait until position (P*) TIMER

appears on the display.

4.2.6.2 Activating the timer function

Follow the steps below for activating the timer control:

• Place the appliance in the standby (pilot burner) position

using button

(small ﬂ ame).

• Set the day/night temperature if you have not yet done so;

for this, see section 4.2.5.1.

• Set the timer times P1 ✹ TIMER, P1  TIMER,

P2 ✹ TIMER and P2  TIMER.

• Choose the (P*) TIMER function using the SET button.

4.2.7 Replacing the battery

If the battery is almost empty, the display will show “BATT”.

To replace the battery, proceed as follows:

• Remove the cover at the back side of the remote control.

• Disconnect the 9V block battery from / connect the 9V

block battery to the connector.

!Caution - Observe the “+” and “-” poles of the

batteries and the connector;

- Use alkaline batteries;

- Batteries are regarded as “small chemical

waste” and may therefore not be

disposed with the household rubbish.

• Place the battery in the holder.

• Replace the cover.

5. Maintenance

At least once per year, the appliance should be checked for

proper and safe operation.

- Your appliance should be maintained by a

competent installer in the ﬁ eld of

atmospheric gas-ﬁ red heating;

- Have a cracked or broken pane replaced

immediately;

- Do not make any changes to the

appliance yourself.

Caution

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU GLOBAL 70 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU GLOBAL 70

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info