Bedienungsanleitung DRU STYLE 3 (Seite 12 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Norwegisch)

571688

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Foreword

Dear Customer,

We would like to thank you for buying this DRU prod-

uct. Our products have been designed and produced to

meet the highest possible quality, performance and safety

requirements, allowing you to enjoy years of problem-free

use.

In this booklet you will find instructions for the installation

and use of your new appliance. Please read these instruc-

tions and the manual carefully to familiarize yourself with

the appliance. If you require any further support, please do

not hesitate to contact your supplier.

Unpacking

Once the heater has been unpacked, all packaging should

be disposed of in the regular manner.

Connection

This appliance should be connected by a registered install-

er.

INSTRUCTIONS FOR INSTALLATION

Type of gas

This appliance can only be used and is only suitable for the

country and the type of gas mentioned on the type iden-

tification tag. Please check that the local gas and pressure

correspond with the specifications on the type identifica-

tion tag. All regulations regarding gas installation, includ-

ing any local regulations, must be observed at all times.

Installation and maintenance of the appliance should be

performed by a professional certified expert with proven

knowledge and demonstrable competence in this field.

A professional expert takes all technical aspects such as

heat output and gas connection into account, as well as

the flue gas discharge requirements. The installation

manual will give you the information you need to install

the appliance in such a way that it will operate properly

and safely. If the installation instruction is not clear,

national/local regulations must be observed.

To operate the heater on propane, it should be converted

by a competend person. A conversion set can be ordered

through your supplier.

Important

• Keep curtains and any other flammable materials at least

50cm away form the appliance.

• Caution! Touching the heater when hot can cause burns

and blisters!

• The appliance should be installed and maintained by a

registered installer.

• Do not install any so-called dust filter on or under the

casing.

• Do not hang wet clothes and towels etc. on the heater to

dry.

• The appliance was designed for atmospheric and heating

purposes. This means that all visible surfaces, including the

glass pane, can become hotter than 100C°. It is recom-

mended to always place a protective grating in front of

the appliance when there are children, elderly people or

handicapped persons in the same room as the appliance.

If it is possible that vulnerable people are regularly present

in the room with no supervision, a fixed guard should be

mounted around the appliance.

General

The appliance can be mounted either on a wall of incom-

bustible material (e.g. stone or concrete) or on a wall of

combustible material (e.g. wood). Style 3-01, 4-01 and 5-01

on propane (G31) can be placed in vehicles pulling mobile

units, provided the following is observed:

• When the appliance is working, the mobile unit must be

standing still;

• When the vehicle pulling the mobile unit is being filled

with fuel, the appliance must be switched off;

• If glass is broken, switch off the appliance and contact an

installer;

• In case of a gas leak, switch off the appliance as well as the

gas supply tap and contact an installer;

• Flue gas discharge must remain unobstructed at all times.

Installation to a wall of non-flammable material

(fig. 6, 8, pg. 58, 59)

The models are suitable for hanging installation only. Allow

at least 1 metre’s clearance above the heater to enable

sufficient heat circulation. When installed hanging, at least

1 m free space should be kept above the appliance to

allow sufficient heat dissipation. When intalled standing,

the bottom of the mounting sheet (2) should stand on the

floor, this is the minimum height between the floor and

centre of wall duct (size F. fig 6, 8, pg. 58, 59).

The mounting plate (2) serves as a template to mark the

position of the duct. To be able to hang the casing over

the interior, a minimal clearance of 25 mm must be allo-

wed between the appliance and a windowsill or suchlike.

The minimum clear installation height (Y) required for

each of the various models is listed in the table on page

60.

The standard wall duct

Drill a horizontal hole in the wall, ø E to take the air-sup-

ply pipe. The wall duct should slope at an angle of approx.

2º.

The standard wall duct is suitable for walls with a thick-

ness of 50 – 330 mm and the standard extended wall duct

for walls with a thickness of 50 – 600 mm. Depending on

the thickness of the wall, the inlet and outlet pipes should

be made to length, i.e.:

INSTRUCTIONS FOR INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU STYLE 3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU STYLE 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info