Bedienungsanleitung DRU STYLE 3 (Seite 14 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Norwegisch)

571688

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

(10) stick through the clamps (11). Attach screw nuts and

washers to the bolts (10) and tighten closely up to the

stop. Then slide the screw spindle (12) into the clamp

(13). Fix the screw nut and washer to the screw spindle

(12) and tighten until the interior is standing parallel to the

wall.

N.B. If easy accessible, e.g. on the ground floor, the out-

let pipe can also be mounted from the outside after the

grid interior sheet and the basket have been disassembled.

STYLE 4-01 and 5-01:

After fitting heat-exchanger fix thermostat phial in clip

provided at rear of backplat (R.H.S.).

Connection of the gas supply

For the different types are the connections as mentioned

below:

• STYLE 3-01 3/8” inner thread

• STYLE 4-01, 5-01 3/8” outer thread

If the supply pipe enters the appliance through the back

plate, press out the disc in the plate. An approved con-

necting tap with coupling should be used in the supply

pipe (For Belgium this should be B.G.V. approved). The

connecting tap with coupling should be fitted outside the

casing. Furthermore:

• Expel all air from the supply pipes/hoses before coupling

to the appliance.

• Do not turn the coupling tap when connecting it to the

gas supply.

• Avoid any pressure on the control tap and pipes.

• Check that all connections are gastight.

Operations

The manufacturer has made the appliance suitable for

the type of gas as indicated on the type identification tag.

Check that the gas pre-pressure and burner pressure cor-

respond with what is stated on the type plate. If necessary,

use the control screw to correct the burner pressure.

The control screw for burner pressure is located behind

the cover on the gas control. This cover can be removed

by removing the screw and clicking loose the lip on the

left side by means of a screwdriver. The thermostat

regulates modulatingly between “full power setting” and

“low power setting” and , when little heat is required, in

two settings, i.e. “low” or “off”. In this situation, the pilot

light keeps burning. The “low” setting can only be checked

when the room temperature is higher than

± 15°C (60°F).

The low setting

The low setting has been adjusted to ± 20% of the full

consumption. The low setting screw has been fully tight-

ened and is supplied with the correct low setting bore.

This is not adjustable.

Pilot light burner

Upon delivery, the pilot light burner has the correct con-

sumption by means of a nozzle inside the pilot light burner.

The pilot light burner needs no adjustment.

Putting the casing in its place

From the top, hang the casing over the back sheet, taking

care that the hooks of the casing fit into the notches of

the back sheet and that the operating buttons fit into the

appropriate opening in the casing.

INSTRUCTIONS FOR INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DRU STYLE 3 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DRU STYLE 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info