Bedienungsanleitung Dual Saw CS 490 (Seite 27 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Türkisch)

578050

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

WARNING!

The saw blades were speciﬁcally developed for the DUALSAW. Saw blades of another type may be

used under certain circumstances. The use of other saw blades is not safe and may cause severe

injuries.

WARNING!

Disconnect the power cable from the socket and let the saw blades cool down before you remove

them.

FITTING THE FRONT HOLDING HANDLE

• Screw the front holding handle in the saw, as displayed in Figure 2.

• Tighten the holding handle with the bolt.

REMOVE THE SAW BLADES

1. Press the spindle lock to arrest the saw blade. (Fig. 3)

2. Turn the counter bolt using saw blade key. (Fig. 4)

3. Remove the counter bolt and the washer from the saw blade. (Fig. 5)

4. Open the bottom protective lid for the saw blade. (Fig. 6)

5. Lift the lid and remove Blade 1. (Fig. 7)

6. Lift the lid and remove Blade 2. (Fig. 8)

FITTING THE SAW BLADES

7. Establish which of the new DUALSAW saw blades is Blade 1 (Face 1) or Blade 2 (Face 2). (Fig. 9)

8. Open the bottom protective lid and apply Blade 2 on the saw on the external ﬁtting shaft. (Fig. 10)

9. Place Blade 1 (Face 1) on Blade 2 (Face 2) and place both on the internal ﬁtting shaft. (Fig. 11)

10. Place the washer and the counter bolt on the shaft. (Fig. 12)

11. Tighten the counter bolt with the saw blade key. (Fig. 13)

DUALSAW SAW BLADES

• Ensure that the saw blades are clean, sharp and correctly adjusted. When using blunt saw blades, the

saw is under greater strain and the risk of recoils increases. Keep the replacement saw blades ready so

that you can always use sharp saw blades.

• Resin and rubber-like residues on the saw blade slow down the cutting speed of the saw. Use a special

solvent for resin, hot water or a grease remover to remove adhesive residues. Do NOT use petrol.

OPERATION

PROTECTIVE LIDS FOR SAW BLADES

• The bottom protective lid placed on the saw serves your protection and your safety. On the protective

lid, NO modiﬁcations may be made UNDER ANY CIRCUMSTANCES. If the protective lid is damaged or

moves only slowly or not smoothly, the saw may NOT be used until the protective lid has been repaired

or replaced. Contact customer services. Maintain the correct operating position of the protective lid

while using the saw.

• The protective lid fulﬁls its intended use if it can move smoothly and subsequently returns to the closed

position. Contact customer services if the bottom protective lid no longer closes automatically before

you continue to use the tool.

WARNING!

Do not use the saw if the correct function of the saw blade protective lid is not ensured. The

protective lid should be checked before any commissioning of the saw for its operability. If the saw

falls to the ground, the bottom protective lid and the anti-shock bar must be checked for damage

and their operability for all cut depths.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dual Saw CS 490 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info