633970
10
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
8
3.2.1
Threading of needle thread
Pass the needle thread according to fig. 9.
- through the reel stand,
- from right through the thread guide O,
- from right through the upper hole in the thread guide L,
- from left through the middle hole of the thread guide L,
- from right through the lower hole of the thread guide L,
- counter-clockwise around the adjustable needle thread pre-tension K
- back through the lower hole of the thread guide I,
- clockwise over the thread guide I,
- counter-clockwise in the adjustable needle thread main tension H, clockwise in the thread guide F,
up to the hook,
- from outside below the pulling spring D,
- from below behind the thread guide E,
- from below behind the adjustable thread guide G,
- from right through the lower hole in the thread take-up lever,
- from above through the thread guide E (if available),
- behind the thread guide C,
- through the thread guide R,
- to the hook through the needle and advance some 8,0 cm
Thread tension
3.3
3.3.1
Adjusting the thread tensions
Rule 1:
A good seam pattern with regularly tightened stitches is often obtained only by regulating the needle
thread tensioning elements, principally by the needle thread main tension H.
Indication 1:
When adapting the needle thread tension, loosen first the needle thread pre-tension K and regulate only
the needle thread main tension H, until the bobbin thread and the needle thread are locked in the material,
fig. 5.
The needle thread pre-tension should be regulated finally, because it is always lower than the main
tension of the needle thread.
Rule 2:
In case of a general adjustment of the thread tensioning elements, adjust first the bobbin thread tension P
for a low value and adapt it then to the needle thread tension.
Indication 2:
For a lockstitch seam, the low bobbin thread tension can already be influenced during the winding
process by the adjustable bobbin winder pre-tension P. The bobbin thread pre-tension P should be
adjusted so that the bobbin thread is wound regularly with the lowest possible tension.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Durkopp Adler 267 - 2016 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info