633970
11
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
9
3.3.2
Lifting the thread tension
- automatically with the "presser foot lift"
Bobbin thread
3.4
According to the sub-class, see the maximum limits of the suitable
bobbin thread in the table 1.1.
3.4.1
Winding the bobbin thread (fig. 3)
Pass the bobbin thread
- through the reel stand,
- from left through the rear hole in the thread guide U,
- clockwise between the disks around the adjustable bobbin winder
pre-tension U,
- from right back through the rear hole in the thread guide U,
- from left through the middle hole in the thread guide U,
- from right through the front hole in the thread guide U,
- counter-clock wise several times around the bobbin T,
- pass the excessive thread end in the knife for cutting it off,
- press the bobbin winder lever M. The winder will stop automatically.
- Pull the bobbin thread in the knife for cutting it off.
The bobbin winder pre-tension U should be set so Low that the thread is wound regularly at low tension.
When winding at an excessive pre-tension, the aluminium bobbins T may be separated and
considerable thread cutting disturbances may occur.
3.4.2
Bobbin change
For changing the bobbin,
- Move the thread take-up lever to its topmost point,
- Swing the lever B upwards (for arresting the presser foot in its upper position),
- Lift the flap and remove the bobbin case top from the hook,
- Place the other bobbin so that the bobbin rotates contrary to the thread pulling direction,
- Pull the bobbin thread under the spring d in the slit and advance
it from below through the hole for about 8,0 cm,
- Hold the bobbin case top with bobbin at the free thread end and place it into the hook,
close the fIap.
3.4.3
Adjusting the bobbin thread tension
Rule 1:
Work with the lowest possible bobbin thread tension.
Indication 1:
For correcting, turn the screw.
Rule 2:
For a lockstitch seam, the low bobbin thread tension can already be influenced during the winding
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Durkopp Adler 267 - 2016 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info