Bedienungsanleitung Dyson CU Beam Down (Seite 72 von 80) (Alle Sprachen)

761229

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

USEN

IMPORTANT SAFETY INSTRUCTIONS

BEFORE INSTALLING OR USING THIS FIXTURE READ ALL

INSTRUCTIONS AND CAUTIONARY MARKINGS IN THIS MANUAL

AND THE INSTALLATION NOTES

WARNING

Risk of electric shock! If casing is removed or handled, improperly

the internal components of the fixture may cause harm or become

permanently damaged. Do not expose the internal mechanisms/

components of this fixture to moisture.

1. All electrical installation and repair work should be carried out by a

qualified electrician or Dyson Field Service Technician in accordance

with current local codes or regulations.

2. Do not connect any DALI/1-10V/0-10V/PWM terminals to mains power.

DALI wires are NOT SELV and should never be considered safe to touch.

Basic level of isolation or better is required between DALI wires and

mains cabling.

3. To prevent movement and strain on the terminals, positive means of field

wiring securement must be provided during installation. The field wiring

shall be secured less than 3 inches from the cord entry and considered

with National Electrical Code.

4. This fixture must be installed in accordance with NEC or your

local electrical code. If you are not familiar with these codes and

requirements, consult a qualified electrician. This fixture should be

installed with appropriate fixings for the installation environment.

Conformity and compliance is the responsibility of the installer.

5. If any part of the fixture is not working as it should, has received a sharp

blow, has been dropped, damaged, left outdoors, or been in contact

with water, do not use and contact the Dyson Helpline.

6. CAUTION: Possibly hazardous optical radiation emitted from this

fixture. Do not stare at the light source. May be harmful to the eye.

The fixture should be positioned so that prolonged staring into the light

source at a distance closer than 2 ft (0.6m) is not expected.

7. Do not install or use with a damaged suspension cable. If the suspension

cable supplied is damaged it must be replaced by Dyson, its service

agent or similiarly qualified person in order to avoid a hazard.

8. This fixture is compatible with DALI/1-10V/0-10V/PWM compliant

control systems.

9. Use a dry, lint free cloth or compressed air (solvent and moisture free) to

clean the fixture. Ensure the fixture is switched off before cleaning.

10. Ensure no pipe work (gas, water, air) or electrical cables, wires or

ductwork are located directly behind the drilling/mounting area.

11. Check that the electrical supply corresponds to that shown on the rating

plate, if the fixture is connected to any electrical supply other than that

stated on the rating plate permanent damage or improper/unsafe

operation of the fixture may result.

12. The fixture must be earthed.

13. The fixture is designed for dry, internal location only. Operating

environment range 0°C (32°F) to 40°C (104°F) and 10-95% RH

non-condensing.

READ AND SAVE

THESE INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Dyson CU Beam Down Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson CU Beam Down

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info