Bedienungsanleitung Dyson DC40 (Seite 8 von 12) (Englisch)

702449

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

USING YOUR DYSON APPLIANCE

PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON

OPERATING MANUAL BEFORE PROCEEDING.

ASSEMBLY

• Lie the appliance on its back.

• Attach the cleaner head by sliding it on to the connections on the lower front part

of the ball. Ensure the electrical plug on the cleaner head fits into the twin-block

connection on the body of the appliance, which is directly above the airway.

Push firmly: the cleaner head will click into place.

• Stand the appliance up straight.

• Attach the wand handle by sliding it on to the top of the appliance. The spring

clip in the handle will click into place.

• Ensure the hose is straight. Press the red button on the hose. Slide the wand into

the hose.

• Ensure the hose and wand sit in the recess of the handle. Slide the end of the

wand down into the handle to secure it.

• Close the wand cap.

• Slide the tool holder onto the side of the duct as shown.

• Ensure the cyclone and clear bin unit is secured to the main body of the

appliance.

• Attach the tools as shown. In use, the tools can be attached to either the hose or

the wand.

• Wind the cable anti-clockwise around the cable hooks. Secure with the clip.

• To watch a short online video visit:

UK – www.dyson.co.uk/DC40gettingstarted

ROI – www.dyson.ie/DC40gettingstarted

OPERATION

• Unwind the cable.

• Plug the appliance into the mains electricity supply.

• To switch ‘ON’ or ‘OFF’ press the power button, located as shown.

• To use, recline the handle. The stabiliser stand will automatically lift up.

• After use, return the appliance to the upright position, pushing it firmly into

place. The stabiliser wheels will automatically lower.

• Then unplug the appliance, coil the cable safely and put the appliance away.

• Switch ‘OFF’ the appliance, unplug and ensure it is upright before:

– changing or using tools

– removing the hose or airway inspection parts.

• Use the cyclone carry handle to carry the appliance.

ATTACHMENTS

• To release the wand, open the wand cap and pull the red tube up and away from

the handle until it clicks into place.

• Should you wish to use the hose without the wand, follow the above instruction

and press the red button to release the wand from the hose.

CARPETS OR HARD FLOORS

• The brush bar will always default to ‘ON’ (spinning) each time you switch the

appliance ‘ON’ and recline it for cleaning.

• The brush bar will not rotate when the appliance is upright.

• To switch the brush bar off (e.g. for delicate rugs and hard floors):

– switch the appliance ‘ON’

– recline the appliance

– press the brush bar ‘ON/OFF’ button – the brush bar will stop spinning.

• The brush bar will automatically stop if it becomes obstructed. See ‘Brush bar –

clearing obstructions’.

• Before vacuuming your flooring, rugs and carpets, check the manufacturer’s

recommended cleaning instructions.

• Some carpets may fuzz if a rotating brush bar is used when vacuuming. If this

happens, we recommend vacuuming in ‘hard floor’ mode and consulting with

the flooring manufacturer.

• The brush bar on the appliance may damage some carpet types. If you are

unsure, turn ‘OFF’ the brush bar.

LOOKING AFTER YOUR DYSON APPLIANCE

• Do not carry out any maintenance or repair work other than that shown in this

Dyson Operating Manual, or advised by the Dyson Helpline.

• Only use parts recommended by Dyson. If you do not this could invalidate

your guarantee.

• Store the appliance indoors. Do not use or store it below 0°C. Ensure the

appliance is at room temperature before operating.

• Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning

agents, polishes or air fresheners on any part of the appliance.

• If used in a garage, always wipe the base plate, ball and stabiliser wheels with

a dry cloth after vacuuming to clean off any sand, dirt, or pebbles that could

damage delicate floors.

VACUUMING

CAUTION:

• Do not use without the clear bin and filters in place.

• Fine dust such as plaster dust or flour should only be vacuumed in very small

amounts.

• Do not use the appliance to pick up sharp hard objects, small toys, pins, paper

clips, etc. They may damage the appliance.

• When vacuuming, certain carpets may generate small static charges in the

clear bin or wand. These are harmless and are not associated with the mains

electricity supply. To minimise any effect from this, do not put your hand or insert

any object into the clear bin unless you have first emptied it and rinsed it out with

cold water (see ‘Cleaning the clear bin’).

• Powerful suction can cause the hose to ‘pull back’ – please take care.

• Do not work with the appliance above you on the stairs.

• Do not put the appliance on chairs, tables, etc.

• Before vacuuming highly polished floors, such as wood or lino, first check that

the underside of the floor tool and its brushes are free from foreign objects that

could cause marking.

• Do not leave the cleaner head in one place on delicate floors.

EMPTYING THE CLEAR BIN

• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.

• Switch ‘OFF’ and unplug before emptying the clear bin.

• To remove the cyclone and clear bin unit, press down on the red button at the

rear of the carrying handle on the cyclone.

• To release the dirt, press all the way down on the red button at the rear of the

carrying handle on the cyclone.

• To minimise dust/allergen contact when emptying, encase the clear bin tightly in

a plastic bag and empty.

• Remove the clear bin carefully.

• Seal the bag tightly, dispose as normal.

• To refit:

– close the clear bin base so it clicks into place

– push the cyclone and clear bin unit into the main body of the appliance; it will

click into place

– ensure the cyclone and clear bin unit is secure.

• For a free fact sheet visit: www.dyson.co.uk/technology/allergy

CLEANING THE CLEAR BIN

• Remove the cyclone and clear bin (instructions above).

• To separate the cyclone unit from the clear bin press the red button to open

the clear bin base. This exposes a small silver button behind the red opening

mechanism. Press the silver button and separate the cyclone unit from the

clear bin.

• Clean the clear bin with cold water only.

• Ensure the clear bin is completely dry before replacing.

• Do not use detergents, polishes or air fresheners to clean the clear bin.

• Do not put the clear bin in a dishwasher.

• Do not immerse the whole cyclone unit in water or pour water into the cyclones.

• Clean the cyclone shroud with a dry cloth or dry brush to remove lint and dust.

• To refit the bin to the cyclone unit:

– fit the cyclone shroud into the clear bin so that the silver button clicks and

engages

– close the clear bin base so it clicks into place

– push the cyclone and clear bin unit into the main body of the appliance; it will

click into place

– ensure the cyclone and clear bin unit is secure.

WASHING YOUR FILTERS

• Your appliance has two washable filters, located as shown.

• Check and wash the filters regularly according to instructions to maintain

performance.

• Switch ‘OFF’ and unplug before checking or removing the filters.

• The filters may require more frequent washing if vacuuming fine dust.

• Wash with cold water only. Do not use detergents.

• Do not put filters in a dishwasher, washing machine, tumble dryer, oven,

microwave or near a naked flame.

• To remove filter A see the ‘Wash filters’ section in this Dyson Operating Manual.

• After washing lay the filter on its side and leave at least 24 hours to dry

completely before refitting.

• To remove filter B:

– turn the central locking dial on the outer cover of the ball anti-clockwise until

the cover is released

– lift off the cover

– turn the filter one-quarter anti-clockwise to release.

• Filter B should be rinsed and tapped out until the water runs clean, then tapped

out again to ensure all excess water is removed. Leave to dry completely for

24 hours.

• It is normal for the filter in the ball to turn grey in colour.

• To refit filter B:

– refit the filter on to the ball

– secure the filter by turning it one-quarter turn clockwise.

• When refitting the outer cover of the ball, keep turning the central locking dial

clockwise. When it starts to click it is locked.

• To watch a short online video visit:

UK – www.dyson.co.uk/DC40filterwash

ROI – www.dyson.ie/DC40filterwash

Dyson DC40 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info