Bedienungsanleitung Dyson V8 (Seite 20 von 41) (Alle Sprachen)

665103

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

• Reattach the end cap to the brush bar.

• Slide the large brush bar back onto the cleaner head, around the motor. The

end cap should be in the open position as shown. Once in place, rotate the end

cap back into the closed position.

• Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is

fully turned and the base plate and the brush bars are secure.

WASHING THE FILTERS

• Your appliance has two washable filters; wash the filters at least once a month

according to the following instructions to maintain performance. More frequent

washing may be required where the user: vacuums fine dust, operates mainly in

'Powerful suction' mode, or uses the machine intensively.

WASHING FILTER A

• Ensure the appliance is disconnected from the charger before removing the

filter. Be careful not to pull the ‘ON’ trigger.

• Check and wash the filter regularly according to instructions to

maintain performance.

• The filter may require more frequent washing if vacuuming fine dust or if used

mainly in ‘Powerful suction’ mode.

• To remove the filter, lift it out of the top of the appliance.

• Wash the filter with cold water only. No hot water and no detergents.

• Run water over the outside of the filter until the water runs clear.

• Squeeze and twist with both hands to make sure the excess water is removed.

• Leave the filter to dry completely for a minimum of 24 hours.

• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,

microwave or near a naked flame.

• To refit, place the dry filter back into the top of the appliance. Make sure it is

seated properly.

WASHING FILTER B

• To remove the filter, twist anti clockwise to the open position and pull away from

the appliance.

• Wash the inside of the filter under cold running water, rotating the filter to

ensure all pleats are covered.

• Gently tap the filter against the side of the sink several times to remove

any debris.

• Repeat this process 4-5 times until the filter is clean.

• Place the filter upright, with the Max button facing upwards, and leave to dry

completely for a minimum of 24 hours.

• To refit, return the filter to the open position and twist clockwise until it clicks

into place.

BLOCKAGES – AUTOMATIC CUT-OUT

• This appliance is fitted with an automatic cut-out.

• If any part becomes blocked the appliance may automatically cut out.

• This will happen after the motor pulses a number of times (i.e switches on and

off in quick succession).

• Leave to cool down before looking for blockages.

• Ensure the appliance is disconnected from the charger before looking for

blockages. Failure to do so could result in personal injury.

• Clear any blockage before restarting.

• Refit all parts securely before using.

• Clearing blockages is not covered by your guarantee.

LOOKING FOR BLOCKAGES

The motor will pulse when there is a blockage. Please follow the instructions

below to locate the blockage:

• Ensure the appliance is disconnected from the charger before looking for

blockages. Be careful not to pull the ‘ON’ trigger.

• Do not operate while checking for blockages. Doing so could result in

personal injury.

• Beware of sharp objects when checking for blockages.

• To check for blockages in the main body of the appliance, remove the clear

bin and cyclone as per the instructions in the cleaning the clear bin section and

remove the blockage. Please consult the 'Stubborn blockages' section of the

illustrations for further guidance.

• If you cannot clear an obstruction you may need to remove the brush bars,

please follow the instructions below:

– To remove the soft roller cleanerhead brush bars, please refer to the 'Washing

the soft roller cleanerhead brush bars' section. Remove the obstruction and

replace the brush bars as shown in the ‘Washing the soft roller cleanerhead

brush bars’ section. Ensure that the fastener is fully turned and the base plate

and brush bars are secure before operating the appliance.

– To remove the brush bar from the direct drive cleanerhead, use a coin to

unlock the fastener and slide the brush bar out of the cleanerhead. Remove

the obstruction. Replace the brush bar and secure it by tightening the fastener.

Ensure it is fixed firmly before operating the appliance.

• This appliance has carbon fibre brushes. Take care if coming into contact with

them, as they may cause minor skin irritation. Wash your hands after handling

the brushes.

• Refit all parts securely before using.

• Clearing blockages is not covered by your guarantee.

CHARGING AND STORING

• This appliance will switch ‘OFF’ if the battery temperature is below 3°C

(37.4°F). This is designed to protect the motor and battery. Do not charge the

appliance and then move it to an area with a temperature below 3°C (37.4°F)

for storage purposes.

• To help prolong battery life, avoid recharging immediately after a full discharge.

Allow to cool for a few minutes.

• Avoid using the appliance with the battery flush to a surface. This will help it run

cooler and prolong battery run time and life.

BATTERY SAFETY INSTRUCTIONS

• If the battery needs replacing please contact the Dyson Helpline.

• Use only Dyson chargers for charging this Dyson appliance.

• The battery is a sealed unit and under normal circumstances poses no safety

concerns. In the unlikely event that liquid leaks from the battery do not touch the

liquid and observe the following precautions:

– Skin contact – can cause irritation. Wash with soap and water.

– Inhalation – can cause respiratory irritation. Expose to fresh air and seek

medical advice.

– Eye contact – can cause irritation. Immediately flush eyes thoroughly with water

for at least 15minutes. Seek medical attention.

– Disposal – wear gloves to handle the battery and dispose of immediately,

following local ordinances or regulations.

CAUTION

The battery used in this device may present a risk of fire or chemical burn if

mistreated. Do not disassemble, short contacts, heat above 60°C(140°F), or

incinerate. Keep away from children. Do not disassemble and do not dispose of

in fire.

DISPOSAL INFORMATION

• Dispose of or recycle the battery in accordance with local ordinances

or regulations.

• This marking indicates that this product should not be disposed with other

household wastes throughout the EU. To prevent possible harm to the

environment or human health from uncontrolled waste disposal, recycle it

responsibly to promote the sustainable reuse of material resources. To return

your used device, please use the return and collection systems or contact

the retailer where the product was purchased. They can take this product for

environmental safe recycling.

• Keep the used batteries away from children as these can still harm children

if swallowed.

• Dyson products are made from high grade recyclable materials. Recycle

where possible.

• Your filter unit is non-washable and non-recyclable.

• The battery should be removed from the product before disposal.

GUARANTEE TERMS AND CONDITIONS

DYSON CUSTOMER CARE

THANK YOU FOR CHOOSING TO BUY A DYSON APPLIANCE

After registering your free 2 year guarantee, your Dyson appliance will be

covered for parts and labour for 2 years from the date of purchase, subject

to the terms of the guarantee. If you have any questions about your Dyson

appliance, call the Dyson Helpline with your serial number and details of where/

when you bought the appliance.

Most questions can be solved over the phone by one of our trained Dyson

Helpline staff.

Alternatively, visit www.dyson.com for online help, general tips and useful

information about Dyson.

If your Dyson appliance needs a service, call the Dyson Helpline so we can

discuss the available options. If your Dyson appliance is under guarantee, and

the repair is covered, it will be repaired at no cost.

PLEASE REGISTER AS A DYSON

APPLIANCE OWNER

To help us ensure you receive prompt and efficient service, please register as a

Dyson appliance owner. There are two ways to do this:

• Online at www.dyson.com

• Telephone the Dyson Helpline.

This will confirm ownership of your Dyson appliance in the event of an insurance

loss, and enable us to contact you if necessary.

LIMITED 2 YEAR GUARANTEE

TERMS AND CONDITIONS OF THE DYSON 2 YEAR LIMITED GUARANTEE

WHAT IS COVERED

• The repair or replacement of your Dyson appliance (at Dyson’s discretion) if it

is found to be defective due to faulty materials, workmanship or function within

2 years of purchase or delivery (if any part is no longer available or out of

manufacture Dyson will replace it with a functional replacement part).

• Where this machine is sold outside of the EU, this warranty will only be valid if

the appliance is used in the country in which it was sold.

• Where this machine is sold within the EU, this warranty will only be valid (i) if

the appliance is used in the country in which it was sold or (ii) if the appliance is

used in Austria, Belgium, France, Germany, Ireland, Italy, Netherlands, Spain or

the United Kingdom and the same model as this appliance is sold at the same

voltage rating in the relevant country.

WHAT IS NOT COVERED

Dyson does not guarantee the repair or replacement of a product where a

defect is the result of:

• Accidental damage, faults caused by negligent use or care, misuse, neglect,

careless operation or handling of the appliance which is not in accordance with

the Dyson Operating Manual.

• Use of the appliance for anything other than normal domestic

household purposes.

• Use of parts not assembled or installed in accordance with the instructions

of Dyson.

USING YOUR DYSON APPLIANCE

PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON

OPERATING MANUAL BEFORE PROCEEDING.

OPERATION

• Do not use outdoors or on wet surfaces or to vacuum water or other liquids –

electric shock could occur.

• Ensure the appliance remains upright in use and in storage. Dirt and debris may

be released if it is turned upside down.

• Do not operate while checking for blockages.

• For domestic indoor and car use only. Do not use it whilst the car is in motion or

while driving.

• To operate the Max mode, locate the switch on the top of the appliance. Slide

the switch to the Max mode position.

• To switch off Max mode, slide the switch back to the Powerful Suction

mode position.

• This product has carbon fibre brushes. Take care if coming into contact with

them, as they may cause minor skin irritation. Wash your hands after handling

the brushes.

DIAGNOSTICS – LIGHTS DURING CHARGING

DIAGNOSTICS – DURING USE

DOCKING STATION INSTALLATION

• Use appropriate mounting hardware for your wall type and ensure that the

docking station is mounted securely. Ensure no pipe work (gas, water, air) or

electrical cables, wires or ductwork are located directly behind the mounting

area. The docking station must be mounted in accordance with regulations

and applicable codes/standards (state and local laws may apply). Dyson

recommends the use of protective clothing, eyeware and materials when

installing the docking station.

CARPETS OR HARD FLOORS

• Before vacuuming your flooring, rugs and carpets, check the manufacturer’s

recommended cleaning instructions.

• The brush bar on the appliance can damage certain carpet types and floors.

Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this

happens, we recommend vacuuming without the motorised floor tool and

consulting with your flooring manufacturer.

• Before vacuuming highly polished floors, such as wood or lino, first check that

the underside of the floor tool and its brushes are free from foreign objects that

could cause marking.

LOOKING AFTER YOUR DYSON APPLIANCE

• Do not carry out any maintenance or repair work other than that shown in this

Dyson Operating Manual, or advised by the Dyson Helpline.

• Only use parts recommended by Dyson. If you do not this could invalidate

your guarantee.

• Store the appliance indoors. Do not use or store it below 3°C (37.4°F). Ensure

the appliance is at room temperature before operating.

• Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning

agents, polishes or air fresheners on any part of the appliance.

VACUUMING

• Do not use without the clear bin and filters in place.

• Fine dirt such as flour should only be vacuumed in very small amounts.

• Do not use the appliance to pick up sharp hard objects, small toys, pins, paper

clips, etc. They may damage the appliance.

• When vacuuming, certain carpets may generate small static charges in the

clear bin or wand. These are harmless and are not associated with the mains

electricity supply. To minimise any effect from this, do not put your hand or

insert any object into the clear bin unless you have first emptied it. Clean the

clear bin with a damp cloth only. (See ‘Cleaning the clear bin’.)

• Use extra care when cleaning on stairs.

• Do not rest the appliance on chairs, tables, etc.

• Do not press down on the nozzle with excessive force when using the appliance

as this may cause damage.

• Do not leave the cleaner head in one place on delicate floors.

• On waxed floors the movement of the cleaner head may create an uneven

lustre. If this happens, wipe with a damp cloth, polish the area with wax, and

wait for it to dry.

EMPTYING THE CLEAR BIN

• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.

• Ensure the appliance is disconnected from the charger before emptying the

clear bin. Be careful not to pull the 'ON' trigger.

• To make emptying the clear bin easier, it is advisable to remove the wand and

floor tool.

• To minimise dust/allergen contact when emptying, encase the clear bin tightly in

a plastic bag and empty.

• To release the dirt, hold the appliance by the handle, pull the red lever back and

lift upwards to release the cyclone. Continue until the bin base automatically

opens and releases the dirt.

• Remove the clear bin carefully from the bag.

• Seal the bag tightly, dispose as normal.

• To close, push the cyclone downwards until it is in the normal position and

manually close the base of the bin – the base will click when it is securely

in place.

CLEANING THE CLEAR BIN

• Ensure the appliance is disconnected from the charger before removing the

clear bin. Be careful not to pull the ‘ON’ trigger.

• Remove the wand and floor tool.

• To remove the cyclone, hold the appliance by the handle, pull the red lever

towards you and lift upwards until the bin opens, then push in the red button

located behind the cyclone and lift the cyclone out.

• To detach the clear bin from the appliance, pull back on the red catch located

at the base, slide the clear bin down and carefully remove forwards from the

main body.

• Clean the clear bin with a damp cloth only.

• Do not use detergents, polishes or air fresheners to clean the clear bin.

• Do not put the clear bin in a dishwasher.

• Ensure the clear bin is completely dry before replacing.

• To replace the clear bin, align the tabs on the clear bin with the grooves on the

main body and slide upwards into place until the catch clicks.

• Slide the cyclone into the grooves of the main body and push downwards until

it is in its normal position and manually close the base of the bin – the base will

click when it is securely in place.

WASHABLE PARTS

Your appliance has washable parts, which require regular cleaning. Follow the

instructions below.

WASHING THE BRUSH BARS

• Your appliance has two washable brush bars, check and wash these regularly

according to the following instructions to maintain performance.

• Ensure the appliance is disconnected from the charger before removing the

brush bar. Be careful not to pull the ‘ON’ trigger.

TO REMOVE, WASH AND REPLACE BRUSH BARS:

• Please refer to the ‘Washing the brush bars’ illustrations alongside the

instructions below.

• Turn the cleaner head upside down so the underside of the cleaner head is

facing you. Use a coin to turn the fastener one quarter anti-clockwise to the

unlocked position.

• Rotate the end cap to the open position. Gently slide the large brush bar away

from the cleaner head.

• Remove the end cap from the large brush bar.

• Lift out the small brush bar from the octagonal end and pull away from the

cleaner head.

• Hold the brush bars under running water and gently rub to remove any lint

or dirt.

• Stand both brush bars upright. Ensure the large brush bar is stood upright as

shown. Leave to dry completely for a minimum of 24 hours.

• Before replacing, check that the brush bars are completely dry. Refit the small

brush bar before the large one. Insert the round end of the small brush bar into

place. Push down the octagonal end until it clicks into place.

Charging, low charge.

Charging, nearly full.

Charger fault – call the Dyson Helpline.

Charging, medium charge.

Fully charged.

Battery fault – call the Dyson Helpline.

High level of charge.

Low level of charge.

Battery fault – call the Dyson

Helpline.

Medium level of charge.

Empty, needs recharging.

Main body fault – call the

Dyson Helpine.

Downloaded from www.vandenborre.be

Dyson V8 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Dyson V8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info