Bedienungsanleitung EasyAlarm CONTROL (Seite 23 von 32) (Englisch)

515345

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

9.2.1 Motion detector activated for presence verification

Symptom Cause and / or remedy

LED is on during WALK TEST, but no

alarm is triggered

 In case of presence verification an alarm is only triggered, if no

motion has been detected over the programmed period ( time-out

can be selected according to section 5.1.2.1)

WALK TEST has been set, but LED is not

 Power supply of the motion detector is missing (=> check cable,

connector and power supply)

 Power supply not on since two minutes (stabilize time of PIR-motion

detector)

Alarming with announcement „emergency

call activated, sensor 1 activated “

 Motion detector has been connected after the unit has been switch on!

Alarming with announcement „emergency

call activated, sensor failure “

 Motion detector has been disconnected after the unit has been switch

on!

9.3 Sensor-1-contact

Symptom Cause and /or remedy

Sensor-1 does not trigger an alarm  Inactive waiting period by switching on the unit or between two alarms

is not expired

 Supervision has been temporarily deactivated (deactivation)

 Supervision is deactivated at current position of the selection switch

(I/II/III) ( section 5.1)

 Motion detection is programmed to verify presence ( section

5.1.2.1), an alarm is only triggered if no motion is detected over a

programmed time.

 Test mode => check section 4.2.3

„Alarm due to sensor 1“ is announced, but

the motion detector has been temporarily

deactivated

 The power supply of the unit has been cut off for a short period

 The function switch has been switched to PROG or OFF after

temporarily deactivation.

9.4 Sensor-2-contact

Symptom Cause and /or remedy

Sensor-2 does not trigger an alarm  Inactive waiting period by switching on the unit or between two alarms

is not expired

 Supervision has been temporarily deactivated (deactivation)

 Supervision is deactivated at current position of the selection switch

(I/II/III) ( section 5.2)

 Sensor-2 is activated as an emergency button ( section 5.2.2)

 Test mode => check section 4.2.3

„Alarm due to sensor 2“ is announced, but

the motion detector has been temporarily

deactivated

 The power supply of the unit has been cut off for a short period

 The function switch has been switched to PROG or OFF after

temporarily deactivation.

9.5 Sensor-3-contact

Symptom Cause and /or remedy

Sensor-3 does not trigger an alarm  Inactive waiting period by switching on the unit or between two alarms

is not expired

 Supervision has been temporarily deactivated (deactivation)

 Supervision is deactivated at current position of the selection switch

(I/II/III) ( section 5.3)

 Contact is still in alarm position. A new alarm can only be triggered,

after the contact returns to its rest position

 Test mode => check section 4.2.3

9.6 Acoustical monitoring

Symptom Cause and /or remedy

noise is not triggering an alarm  Factory setting supports monitoring of acoustics only on pos. III of

selection switch. ( programming can be altered, see section 5.4)

 The unit has been deactivated by DTMF 7 => LED alternatively 4s

on / 4s off

 By switching on the unit or after triggering an alarm, the acoustical

monitoring is not active during the waiting time of 20 seconds (

section 7.3) => LED is lit constantly during the waiting time!

 Depending on the position of the selection switch, an alarm is triggered

with a different delay. Every time the noise exceeds the pre set level,

the LED is on. ( section 7.4)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EasyAlarm CONTROL Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EasyAlarm CONTROL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info