Bedienungsanleitung Easymaxx LS520B-RGB-2M - Z05887 (Seite 4 von 8) (Deutsch, Englisch, Holländisch, Französisch)

703715

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

EN Instructions

Customer Service / Importer:

DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •

✆ +49 38851 314650 *)

*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.

Remote control

1 On/Off switch

2 White light (mixed colour)

3 Flash (ﬂ ashing function)

4 Strobe (slow fading out of

a colour)

5 Fade (slow fading out with

colour change)

6 Smooth (smooth colour

change)

7 Control panel for colour

selection (12 mixed co-

lours)

8 RGB setting (red, green,

blue)

9 Increase/decrease the in-

tensity of colour

Start-up

PLEASE NOTE

■ First connect the LED strips and the connector cables with one

another before you plug the product into a device that is con-

nected with the mains supply.

1. Connecting the cables – Connect the LED strips with each

other or use the connector cables. To do so, connect them

in the following order: LED strip with USB plug → connector

cable → connection piece → LED strip → connector cable etc.

Make sure that all LED strips are similarly aligned (all arrows

are pointing in the same direction). Otherwise the circuit will not

be closed.

2. Cleaning the surfaces – In order for the LED strips to stick in

place, the surface they are stuck to must be smooth, dry and

free of dust, grease and dirt.

3. Sticking the LED strips in place – ATTENTION! When sti-

cking the LED strips in place, they may not be connected

to the mains supply!

Carefully remove the protective foil of a LED strip and stick it

on the desired area. Follow the same steps for the other LED

strips. Make sure that the USB cable is close enough to the

desired USB port!

4. Connecting to the device – Connect the USB cable to the

USB port of the desired device (television or similar).

The backlight is now ready for operation.

Changing the remote control battery

PLEASE NOTE

■ Before inserting the battey, check whether the contacts in the

article and on the battery are clean, and clean them if neces-

sary.

The battery for the remote control has already been inser-

ted. You only have to remove the transport guard.

1. The battery compartment is lo-

cated on the narrow side of the

remote control. Pull it out as

shown.

2. Remove the empty battery

and insert a 3 V battery, type

CR2025. The positive terminal

must point upwards.

3. Place the battery compartment back in the remote control so

that it locks in place.

Use

1. Turn on the LED backlight by pushing the ON button on the

remote control.

2. Select the desired colour or the desired effect and push the

corresponding button on the remote control.

Please note that the colour settings are mixed colours. For

this reason, the colour tints may exhibit minor deviations.

Even white light is a mixed colour and thus not a purely

white colour tint!

3. Set the desired colour brightness using the buttons to increa-

se/decrease the intensity of colour.

4. Push the OFF button to turn off the LED backlight.

Troubleshooting

If the device does not work properly, check whether you are able to

rectify the problem yourself. If the problem cannot be solved with

the steps that are listed, contact the customer service department.

Do not attempt to repair a defective electrical device

yourself!

If the light does not switch on, check

• whether all cables are properly connected with one another.

• whether all LED strips are properly aligned (all arrows are poin-

ting in one direction).

• whether the connected device is properly connected with the

socket.

• whether the socket is defective. Try another socket.

• the fuse for your mains connection.

• whether the battery in the remote control is empty.

Technical data

Product number: 05887

Model number: LS520B-RGB-2M

Voltage supply:

LED strips (USB): 5 V

Remote control: 3 V (1 x 3 V battery,

type CR2025)

Output: 2.5 W

Disposal

Dispose of the packaging material in an environmentally

friendly manner and take it to a recycling centre.

Dispose of the device in an environmentally friendly man-

ner at a recycling centre for used electrical and electronic

devices. More information is available from your local au-

thorities.

Batteries should not be disposed of in the normal household

waste. They should be removed prior to disposal of the de-

vice and disposed of separately from the device at suitable

collection points.

Illustration similar

push

pull

Z 05887 M DS V3 0318

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Easymaxx LS520B-RGB-2M - Z05887 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info