Bedienungsanleitung Easymaxx Z04117 (Seite 3 von 8) (Deutsch, Englisch, Holländisch, Französisch)

703770

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

EN Instructions

Article number: 04117

Dear Customer,

We are delighted that you have chosen the window snap catch.

If you have any questions about the article and about spare parts/

accessories, contact the customer service department via our

website:

www.service-shopping.de

Explanation of Symbols

Safety instructions and warnings: Read through these

carefully and follow them to prevent personal injury and

damage to property.

Supplementary information

Intended Use

• This article is intended to be used to secure single-sash, in-

wardly opening windows with a gap of min. 2.5 cm to max.

5.5 cm. The window wall (reveal) must have a spatial depth of

at least 10 cm.

• The article must not be used to secure apartment doors or

similar doors! Opening from the outside is not possible!

• The article is for personal use only and is not intended for com-

mercial applications.

• The article should only be used as described in these instruc-

tions. Any other use is deemed to be improper.

• The following are excluded from the warranty: all defects

caused by improper handling, damage or unauthorised at-

tempts at repair. This also applies to normal wear and tear.

Safety Instructions

■ Warning of suffocation! Keep children and animals away

from the packaging material.

■ The article is not a toy! Keep it away from children and animals.

■ Use only original spare parts from the manufacturer.

Items Supplied and Article Overview

Unpack all parts and check the items supplied for completeness

and any transport damage. If you ﬁ nd any damage to the compo-

nents, do not use them (!), but contact our customer service de-

partment.

1 Snap cover

2 M8 x 70 stainless

steel bolts (incl.

washer)

3 Packing plate

4 Screw-on block

5 Spreading spring

Not shown:

• 3 x countersunk screw 6x90

• 3 x dowel 8x65

• 1 x hexagon key wrench 5 mm

• 1 x Torx bit TX25

• 4 x self-adhesive rubber buffers

• 2 x self-adhesive small felt pads

• 1 x instructions

• 1 x drilling template

Also required for assembly:

• Drill with 8mm drill bit

• Cordless screwdriver with bit extension (possibly) or Torx

screwdriver or screwdriver with bit attachment

• Pen (possibly)

• Spirit level (possibly)

Assembly

WARNINGS

■ Beware of injuries caused by spreading spring! The spread-

ing spring could cause injuries, e.g. to the eye, when it springs

apart. When it is supplied, the article is mechanically disabled

by a securing tube. This may only be removed when assembly

has been completed!

■ The article may only be attached to stone or concrete walls us-

ing the fastening materials supplied with it. Different fastening

materials may need to be used to attach the article to other sur-

faces. If you are unsure whether the fastening material supplied

is suitable for the wall, seek advice from a specialist stockist.

■ Mount the article in a secure and solid place.

■ Before drilling, ensure that there are no pipes or cables behind

the intended drilling point.

■ Only mount the article in the manner described. A failure to fol-

low the mounting instructions may impair the burglary-inhibiting

effect of the article.

Essential to note:

• The gap size (the gap between the window sash and the wall)

must be at least 2.5 cm.

• The window wall (reveal) must have a spatial depth of at least

10 cm.

Positioning

1. Height: The article should be mount-

ed centrally above the window over

the window handle on the window

wall.

2. Gap from the window sash: The arti-

cle should be ﬁ tted approx. 1 – 2 cm

in front of the window sash so that it

can stop the window with the entire

front surface (A) of the snap cover (1).

Marking Out Drill Holes

3. Fold the drilling template along the fold edge

(green marking).

4. Place the drilling template at

the height you want as follows:

a place the surface with the

drill holes directly against the

window wall and

b slide the drilling template to-

wards the window until the

lay-on edge (red marking)

adjoins the closed window

sash.

5. Align the drilling template horizontally possibly using a spirit

level and mark the three drill holes using a pen or similar imple-

ment.

IMPORTANT: Try out the chosen position with an open

and closed window prior to drilling.

Note the following when you do this:

– the operation of the handle must not be impaired;

– the correct opening of the window must not be impaired when

the window snap catch is closed;

– the open window snap catch should stop the window with the

entire front surface (A) of the snap cover (1).

If the position is not quite right, move the drilling template slightly

and correct the height and / or gap from the window sash (see “Po-

sitioning”). Mark out new drill holes and then try out the position

again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Easymaxx Z04117 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info