Bedienungsanleitung Ecoforest Teide (Seite 30 von 152) (Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

742221

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

1. PLEASE BEWARE THAT...

In order to prevent the risk of accident, a correct installation must be done following the instructions of this

manual. Your ECOFOREST distributor will be available to help you and provide you information related to codes,

assembly and installation norms in your area.

As ecoforest do not have direct control on the installation of your stove, ecoforest do not guarantee it and do

not bear the responsibility of any damage that could result from a bad use or a bad installation.

We carefully recommend the heat calculation to be made by a qualified heating engineer.

We recommend that a confirmed specialist sets up your pellets stove.

Maintenance work to be carried out at the end of the season or for every 500 kg of fuel burned, as well as

any repairs or equipment modifications, must be performed by authorized personnel.

Before getting started with the stove installation, please check section 4.

2. ADVICE AND RECOMMENDATIONS.

2.1. All local regulations, including those referring to national and European standards must be met when

installing the stove.

2.2. The stove must be installed on floors of sufficient bearing capacity and, if the existing construction does not

allow this, the floor must be adapted and made suitable, for example by fitting a load distribution plate.

2.3. Never use petrol, fuel for lanterns, kerosene nor any similar liquid. Keep this kind of fuel away from your

stove.

2.4. Do not try to turn on your stove if some glass is broken.

2.5. Make sure the glass door of the fireplace is well closed while the stove is in operation; also check the

cleaning hatches (if you have touched them).

2.6. Unauthorized modifications are forbidden. Use only spare parts provided by Ecoforest (see exploded view).

2.7. Do not overload the stove; continuous heating efforts might cause premature aging and damage paint (it is

recommended not to exceed 250°C for gas outlet temperature).

2.8. Do not use the stove as a burner.

2.9. To prevent possible electrical shocks, only trained personnel should have access to the sides and the back of

the stove.

2.10. For the Córdoba, Granada and Praga stove models, the air-convection trim cover must be placed at an angle

of 50° (as far as it will go) with respect to the frame, whenever the stove is operational.

Drawing 1

2.11. In order to refill the stove with fuel, the user must open the hopper lid and empty the contents of the fuel

tank carefully, to prevent it from overflowing. See drawing 2 (ECO III).

The fuel loader for the models Córdoba (drawing 3) and Córdoba Glass, Teide and Granada, is removed from

the loading tray by pulling on the handle which is located on the air-convection trim cover. Always load fuel

when the device is cold.

Drawing 2



Air

convection trim cover

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ecoforest Teide Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ecoforest Teide

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info