Bedienungsanleitung Eden HA700 (Seite 12 von 23) (Englisch)

547014

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

3. Using the rear cover as a template, mark the

positions of the fixing holes on the wall.

4. Fix the rear cover to the wall using the two 18mm

screws and 23mm wall plugs. Do not over-tighten

the fixing screws as this may distort or damage the

cover.

5. Configure the Motion Sensor as described below.

Remember that on initial installation that the device

needs to be tested and should therefore be set in

Walk Test Mode.

6. Check that the sensor PCB is located and set in

the correct position to provide the required

detection range. To adjust the PCB position,

simply slide it up or down ensuring that the location

legs are aligned with the required position number

marked on the board.

7. To refit the Motion Sensor to the rear cover and

locate the clips in the top edge into the rear cover.

Push the lower edge of the sensor into place and

refit the fixing screw in the bottom edge of the

Sensor to secure in position. Do not over-tighten

the fixing screws as this may damage the casing.

SETTING THE MOTION SENSORS

Located on the PCB of the Motion Sensor is a

two-position DIP switch (SW2). When conducting the

Walk Test, ensure that the DIP switch SW2 is set as

follows:

SW2 DIP1 DIP2

ON 

OFF 

1. DIP1 of SW2 is used to configure the Motion

Sensor for walk test mode, which allows the

operation of the sensor to be checked during

installation without triggering a Full Alarm.

ON Walk Test mode

OFF Normal mode

Note: Remove batteries before setting the SW2.

Refit batteries after setting the SW2.

Note: On initial installation the sensor should be

set into Walk Test mode ready for testing. Upon

completion of Walk Test mode, set DIP1 of SW2 to

OFF for normal detection mode.

2. The Motion Sensor incorporates an anti-false

alarm feature designed to compensate for

situations where the sensor may be affected by

environmental changes, (e.g. insects, air

temperature, etc). This feature is called

“sensitivity detection” and may be selected for high

or low detection.

The recommended setting is for high sensitivity

detection. However, in cases of extreme

environmental problems or if unattributable false

alarms are experienced, it may be necessary to

select low sensitivity detection.

Set the required sensitivity detection using DIP2 of

SW2 as follows:

ON high sensitivity detection

OFF low sensitivity detection

Note: The higher the sensitivity detection the less

movement will be necessary before the Motion

sensor will trigger the alarm.

3. The setting of the DIP1 & DIP2 of SW2 can be

distinguished from the LED indication as follows:

On/Off

Selection

DIP1 of

SW2

DIP2 of

SW2

Trigger reaction of LED

High

Sensitivity

LED will be on once.

It implies high

sensitivity.

ON Walk Test

mode

Low

Sensitivity

LED will flash twice. It

implies low sensitivity.

Dip Switch(SW2)

Tamper Switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eden HA700 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eden HA700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info