Bedienungsanleitung Eden HA700 (Seite 13 von 23) (Englisch)

547014

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

OFF Normal

mode

High/Low

Sensitivity

LED does not light up.

In summary, the setting of DIP1 & DIP2 of SW2 is

concluded as below:

SW2 DIP1 DIP2

ON Walk Test Mode High sensitivity

OFF Normal Mode Low sensitivity

4. Connect the AA 1.5V battery to the battery

compartment.

Note: When the battery is connected, the LED

behind the lens will flash for 2-3 minutes as

warming-up duration until the Sensor has stabilized

when the LED will then stop flashing and turn OFF.

5. In normal mode, remove the rear cover of the

Motion sensor. The Sensor’s LED will illuminate

and the Control Panel should alarm. It is because

the tamper switch fitted on the Detector has been

activated.

6. When the Sensor is fully installed i.e. rear cover is

refitted; the Sensor will not detect movement for

approximately 2 minutes after each activation.

(This feature is present to conserve battery power

and maximize the battery life).

7. In order to communicate with the Control Panel,

the ID code of the Sensor needs to be learned by

the Control Panel. By pressing the tamper switch

located adjacent to the PCB on the Sensor will

emit the ID code to the Control Panel instantly,

subject to the Control Panel being set at the ID

code learning mode.

TESTING THE MOTION SENSORS

Ensure the system is in test mode.

With the Motion sensor set in Walk Test mode and

mounted in position on the wall, allow 2-3 minutes for

the sensor to stabilize before commencing the Walk

Test.

1. Walk into and move slowly around the protected

area, each time the sensor senses movement the

LED behind the lens will flash. In addition, the

Control Panel will ding dong.

If necessary adjust the detection range by

changing the mounting position of the PCB within

the sensor housing.

Note: In normal operation, the LED behind the

Sensor lens will not flash on movement detection,

(unless the battery is low).

2. Remove the rear cover of the Motion Sensor. (this

is to test the operation of tamper switch) The

Control Panel should ding dong.

3. Press on the Control Panel to exit test

mode.

4. Reconfigure the Motion Sensor for normal mode

by setting DIP1 of SW2 to OFF and refit in

position.

DOOR/WINDOW CONTACT

DETECTOR(S)

The Door/Window contact consists of two parts; a

Detector and a Magnet. They are designed to be

fitted to doors or windows with the Magnet mounted on

the opening part and the Detector mounted on the fixed

frame. Opening the protected door/window will remove

the magnetic field, trigger the Detector and generate an

alarm condition, (if the system is armed).

The Detector is powered by 3 1.5V AAA size batteries

which under normal conditions will have typical life in

excess of 1 year. Under normal battery conditions

with rear cover fitted the LED on the Detector will not

illuminate when the Detector is triggered, (unless in

test mode). However, under low battery conditions this

LED will be illuminated when the detector is triggered.

When this occurs the battery should be replaced as

soon as possible.

Note: The adoption of alkaline battery is highly

recommended.

The Door/Window Contact Detector is of self-contained

wired Magnetic Contact (option). This contact must

be of a normally closed contact type with the contacts

being opened in order to generate an alarm condition.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Eden HA700 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Eden HA700

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info