Bedienungsanleitung EdgeCraft Chef-s Choice - Commercial 2000 (Seite 9 von 12) (Englisch)

663876

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

CLEANING THE SHARPENING MODULE

This appliance is not to be cleaned with a water jet. (NEVER immerse the motor-drive

section in water or spray it with water. When soiled, unplug it and wipe with a damp cloth).

The Sharpening Module should be removed as described. It then can be cleaned by either

of the following methods:

A. Washing by hand:

1. Spray the wheels in each stage with liquid dishwasher detergent.

2. Allow to soak for a few minutes in a pan, bucket or sink to loosen any attached food, etc.

3. Rinse or spray under a strong stream of warm water.

4. Drain on paper towels. Blow dry if clean pressurized air is available.

5. CAUTION... do not towel dry; you may damage the plastic hold-down spring.

6. If diamond wheels are not shiny they may have grease on them. Put sharpening module

through dishwasher.

B. Dishwasher:

1. Spray the wheels in each stage with liquid dishwasher detergent.

2. Put in dishwasher on normal wash cycle.

3. Allow unit to dry in the dishwasher, preferably in a position remote from the heaters.

Periodically remove any metal dust that has collected in the two collection cavities

located below the sharpening and honing stages in the base of the sharpener (under the

Sharpening Module.) With the Sharpening Module removed, simply invert the motor

housing and shake the dust loose. Otherwise remove with a damp sponge. Do not use a

water spray to remove the loose dirt.

INSERTING SHARPENING MODULE

To reinsert the Sharpening Module into the main motor housing, insert the shaft coupling

end of the Sharpening Module into the guide rails at the right end of the sharpener. Then

gently push the Sharpening Module (as in Figure 2) toward the motor housing until it locks

in place. If it resists snapping into the locked position: (1) Pull the module away from the

motor shaft until it fully disengages; (2) turn the motor switch on brieﬂy; (3) then turn it off;

(4) while the motor is coasting to a stop, push the Sharpening Module into place. It will then

automatically snap into position when the spline coupling becomes properly aligned.

CHANGING THE EDGE STOP PLATES

The Edge Stop Plates, especially the pair in front of the sharpening and honing stages, will

in time develop small cuts in the surface where the knife rests during sharpening. This

is normal but the depth of the cuts can be minimized by applying just enough downward

pressure to keep the edge in contact with the Plate. When these cuts approach

” deep,

the Edge Stop Plates should be turned over or replaced. The Plates generally can be

removed simply with a pair of needle nose pliers or by prying them up and out gently with

a pointed tool. They can be inverted, when worn, to expose a fresh edge for contact with

the blade. With experience you will ﬁnd that little or no pressure is necessary against these

plates and that they will last a long time. Replacement Stop Plates are available directly

from your distributor or from EdgeCraft (1-800-342-3255).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EdgeCraft Chef-s Choice - Commercial 2000 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info