Bedienungsanleitung Edgestar PAC1201W (Seite 14 von 23) (Englisch)

727491

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Operating the Control Panel

Use the Power button to turn the portable air conditioner on and off.

Auto-Restart: If power to the unit is interrupted, the air conditioner will restart

itself in its last used mode/settings once power is restored. The compressor will

restart after 3 minutes.

Cooling mode cools and dehumidifies the air. If the ambient temperature drops

below the temperature you selected, the compressor turns off and the unit

functions with the fan only. When the temperature rises above the temperature

you selected, the compressor turns on again.

Whether your desired temperature can actually be reached depends on the

ambient conditions. The room temperature remaining above the set temperature

is normal.

To operate the unit in cooling mode:

1) Make sure the power cord is plugged into a power outlet.

2) Press the Power button.

3) Press the Mode button until the LED indicator next to “Cool” lights up.

4) Select the fan speed by using the Fan button.

5) Set the thermostat by using the Up and Down buttons. The thermostat is

adjustable between 62°F - 88°F in two degree increments.

During the Dehumidifying mode, the unit will condense water out of the air and

accumulate the water in the reservoir. In this mode, you will not be able to select

a different fan speed or adjust the temperature. The fan motor operates at Low

speed.

To operate the unit in dehumidifying mode:

1) Make sure the power cord is plugged into a power outlet.

2) Remove the exhaust hose from the back of the unit.

3) Press the Power button.

4) Press the Mode button until the LED indicator next to “Dry” lights up.

When the portable air conditioner is set to auto mode, it will automatically select

cooling or fan only operation depending on what temperature you have selected

and what the room temperature is near the unit. You cannot change the fan

speed.

To operate the unit in Auto mode:

1. Make sure the unit is powered on. Press the Mode button until the LED

indicator next to “Auto” lights up.

Fan Only mode is used to circulate the air in your room. No temperature

setting is needed.

To operate the unit in Fan Only mode:

1) Plug in the unit to a power outlet and press the Power Button.

2) Press the Mode button until the LED indicator next to “Fan” lights up.

3) Press the Fan button to select the fan speed. You can choose between

High, Medium and Low. The LED indicator next to the speed will light up.

Power

Cooling Mode

Dehumidifying Mode

Automatic Mode

Fan Only Mode

NOTE: The exhaust hose

must be used in Cooling

mode in order to cool a room.

NOTES: While in Dehumidifying mode, you must manually drain the water from the unit. Additionally, the

ambient temperature in the room will probably rise by a few degrees. You will not be able to change the

thermostat temperature while in Dehumidifying Mode. Keep windows and doors closed for the best

dehumidification performance.

NOTE: Fan Only mode

requires that the exhaust

hose be removed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edgestar PAC1201W Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info