Bedienungsanleitung Edgestar PAC1201W (Seite 15 von 23) (Englisch)

727491

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Portable Air Conditioner 12

The Fan button is used to change the fan speed between High Medium,

Low and Auto while in Cooling and Fan Only modes.

Press the Fan button to select the fan speed. The LED indicator light next

to the High, Medium, or Low will light up. The Automatic Fan speed

setting does not have a light.

The timer can be used to either turn the unit on or off after a number of

elapsed hours. The timer is adjustable between 1-10 hours in half-hour

increments and from 10-24 hours in one hour increments.

How to set the unit to automatically turn on:

1) Press the Timer button while the unit is powered off. The Timer On indicator

LED will light up.

2) Use the Up and Down buttons to set the time (displayed in hours). The unit will

count down the time remaining. After the selected time passes, the unit will

automatically turn on.

How to set the unit to automatically turn off:

1) Press the Timer button while the unit is powered on. The Timer Off indicator

LED will light up.

2) Use the Up and Down buttons to set the time (displayed in hours). The unit will

automatically count down and turn off after the selected time elapses.

Note: If the unit displays an E1 or E2 error code, the timer is cancelled.

The LED Display will show the set temperature by default. It will show the room

temperature while in Dehumidify and Fan Only modes. You can switch between

Fahrenheit and Celsius by holding both the Up and Down Buttons simultaneously

for 5 seconds. If you enabled the Timer, the LCD Display will show the hour(s)

set.

Error Codes

The display may show the following error codes:

E1 – Room temperature sensor error.

E2 – Evaporator temperature sensor error.

E4 – Display panel communication error.

If the unit displays the error codes E1, E2, or E4, power the unit off, and then

unplug the unit for 15 minutes. Plug in and power on. If the issue persists, please

contact customer service.

P1 – Bottom reservoir is full.

If the unit displays a P1 error code, drain the unit by following the “Draining the

Unit” section.

The Swing Button is used to adjust the louver swing to the desired angle. The

louver swings up to an angle of 6 degrees for each press of the button. Hold the

swing button for more than 2 seconds to initiate the auto swing features.

(Applicable to models with Swing feature only).

The Sleep Button is used to enable the Sleep mode. During the Sleep mode, the

set temperature will increase by 2 degrees after 30 minutes, then it will increase

by another 2 degrees after an additional 30 minutes and maintain this

temperature for 7 hours before it returns to the original temperature and ends the

Sleep mode. The Sleep mode is not available in Dehumidify and Fan Only

modes.

Fan Button

Timer Button

LED Display

Swing Button

Sleep Button

NOTE: To cancel the

timer, press the Power

button or set the timer to

0.0.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edgestar PAC1201W Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info