Bedienungsanleitung Edilkamin Blade 2 - 12 Up (Seite 23 von 72) (Englisch)

810748

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

INSTALLATION

INSTALLER

FLUE SYSTEM

(

Fumes duct, flue and chimney pot

)

Thsi chapter has been drawn up pursuant to European

regulations EN 13384, EN 1443, EN 1856 and EN

1457. The installer must observe both these and any

other local regulations. This manual does not in any

way substitute such regulations.

The product must be connected to a flue system which

ensures that the fumes produced by combustion are

exhausted in complete safety.

Before positioning the product, the installer must

check that the flue pipe is properly rated.

FUMES DUCT, FLUE

The fumes duct

(which connects the hearth's fumes

outlet with the flue)

outlet with the flue) and the flue itself must, among

other regulatory requirements:

• receive the fumes from a single product (the outlets

of multiple appliances may not be conveyed into

a single flue)

• be routed vertically for the most part

• have no downwards sloping sections

• preferably have a circular internal cross section, or

with a ratio of the sides of less than 1.5

• terminate at roof level with a proper chimney pot:

the flue may not discharge directly from the wall

or into an enclosed space, even if the space in

question is open to the sky

• be made of material rated fire reaction class A1 per

UNI EN 13501 or analogous national regulations.

• be certified, with a chimney plate if metal

• be of uniform cross section or vary in cross section

only immediately after the outlet, not at some mid

point of its length

THE FUMES DUCT

Further to the general prescriptions for the fumes duct

and flue, the fumes duct

• may not be made of flexible metal material

• must be insulated, if routed through unheated

areas or outdoors

• must not be routed through rooms in which the

installation of combustion heat generators is

prohibited, or subject to fire hazard, or which

cannot be inspected.

• must enable the recovery of soot and be open for

inspection

• must have at most 3 bends, through an angle of

no more than 90°

• must have a single horizontal section of length

no more than 3 metri, depending on the draw.

Note in any case that long sections promote the

accumulation of dirt and are harder to keep clean.

Avoid infiltration of condensate water

through the flue. If necessary, mount an

anti-condensate ring – ask your chimney

sweeper for details.

Damage caused by condensate water is

not covered by the warranty.

In some nations, installations with multiple

flues are permitted under certain conditions.

Depending on regional regulations,

additional safety systems are necessary in

case of connection to multiple flues. Your

chimney sweeper/technician will be able to

provide further details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Blade 2 - 12 Up Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Blade 2 - 12 Up

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info