Bedienungsanleitung Edilkamin Blade 2 - 12 Up (Seite 24 von 72) (Englisch)

810748

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

INSTALLATION

INSTALLER

THE FLUE

THE FLUE:

Further to the general prescriptions for the fumes duct

and flue, the flue

• must serve solely to exhaust fumes

• must be correctly sized to satisfy the requirements

of fumes exhaust (EN 13384-1)

• should preferably be insulated, in steel with a

circular internal section. If rectangular, the corners

must have a radius of not less than 20 mm, with a

ratio of the internal dimensions of <1.5

• must normally be at least 1.5 metres in vertical

length

• must have a constant cross section

• must be waterproof and thermally insulated to

ensure a good draw

• must preferable have a collection chamber for

• If pre-existing, must be clean, to prevent the fire

hazard.

• in general, we recommend fitting a tube inside the

existing masonry chimney if its diameter is greater

than 150 mm.

INTUBATED SYSTEM

INTUBATED SYSTEM:

Further to the general prescriptions for the fumes duct

and flue, the intubated system:

• must operate in negative pressure;

• must be open to inspection

• must observe local regulations.

THE CHIMNEY POT

• must be windproof

• must have an internal cross section equivalent to

that of the flue and a fumes outlet at least double

that of the interior of the flue

• for dual flues (which should be spaced at least 2

m apart) the chimney pot receiving the fumes from

the solid fuel appliance or that from the higher

storey, must be at least 50 cm higher than the other

• it must extend beyond the back flow zone (in Italy,

refer to UNI 10683 point 6.5.8.)

• it must allow for maintenance of the chimney

EXTERNAL AIR INTAKE

In general, we suggest two ways for ensuring a proper

flow of combustion air.

Indirect air intake

Install an intake at floor level with effective area (net of

the mesh or other protective equipment) of at least 80

cm2 (10 cm dia.).

To prevent draughts, we recommend installing the

intake behind the stove or behind a radiator.

Installing it in front of the appliance will create

unpleasant draughts.

Direct air intake

Install an air intake of effective area (net of the mesh or

other protective equipment) at least equal to that of the

air intake at the back of the product.

Connect the air intake to the appliance’s air intake with

a tube (which may also be flexible).

We recommend not exceeding a 5 m length and

curving the tube at most 3 time, depending on the

draw of the flue.

The air maty be drawn from an adjacent room only if:

• the flow is taken from permanent and unobstructed

openings communicating with the outdoors;

• the adjacent room is never in underpressure

relative to the outdoors;

• the adjacent room is not a garage. subject to fire

hazard, a bathroom or bedroom

• the adjacent room is not a shared room in the

condominium.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Blade 2 - 12 Up Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Blade 2 - 12 Up

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info