Bedienungsanleitung Edilkamin Demy (Seite 9 von 28) (Englisch)

810764

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

- 9 -

ENGLISH

INSTALLATION

GENERAL NOTES

In Italy it is necessary to refer to the standard declaration of

conformity conforming to Ministerial Decree 37/2008 (pur-

suant to Law 46/1990) and standards UNI 10683 and UNI

10412-2.

In the case of installation in a multiple-tenancy building, con-

tact the building manager before installation.

VERIFY COMPATIBILITY WITH OTHER DEVICES

In Italy the stove MUST NOT be installed in the same space

as type B gas heating equipment (e.g. gas boilers, stoves, and

equipment served by an extraction hood - ref. UNI 10683 and

7129).

In general, the stove could create low pressure in the room,

affecting the operation of such appliances or being affected by

them.

VERIFYTHE POWER SUPPLY CONNECTION

(the plug must be accessible)

The stove is supplied with a power cable that is to be connected

to a 230V 50 Hz socket, preferably tted with a magnetother-

mic switch.

Voltage variations exceeding 10% can damage the stove (unless

already installed, an appropriate differential switch must be

tted).

The electrical system must comply with the law; particularly

verify the efciency of the earthing system. The power line

must have a suitable cross-section for the stove’s power. An

inadequate earthing system can cause anomalies for which

Edilkamin cannot be held liable.

In case of problems with the electrical grid, consult an electri-

cian to evaluate the installation of a sine-wave UPS of at least

800 Va.

AIR INTAKE

The room where the stove is located must have an air intake

with cross section of at least 200 cm2 to ensurereplenishment

of the air consumed by combustion.

Alternatively, the stove air may be taken directly from outside

through a 8 cm steel extension of the pipe.

In this case,there may be condensation problems and it is ne-

cessary to protect the air intake with a grille, which must have

a freesection of at least 50 cm².

The pipe must be less than 1 metre long and have no bends.

It must end with section at 90° facing downwards or be  tted

with a wind guard. In any case all the way air intake duct must

be a free section of at least 50 cm².

The external terminal of the air inlet channel must be protected

with an anti-insect netting that does not reduce the 50 cm²

through passage.

POSITIONING AND DISTANCES FOR FIRE SAFETY

The stove must be installed in compliance with the following

safety conditions:

- minimum distance from ammable materials around the sides

and back of the stove: 20 cm

- ammable materials must not be placed less than 80 cm from

the front of the stove.

If it is not possible to comply with the above-mentioned di-

stances, technical and construction-related provisions must be

taken to prevent re hazards.

If connected to wooden walls or other ammable materials, the

smoke exhaust pipe must be insulated.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Demy Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Demy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info