Bedienungsanleitung Edilkamin Demy (Seite 10 von 28) (Englisch)

810764

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

- 10 -

ENGLISH

INSTALLATION

FLUE

• Before positioning the stove, make sure the ue is suitable

for the smoke produced.

• When installing the stove, the position of the ue must

be taken into account in order to prevent incorrect smoke

duct paths; the size of the ue must comply with the specica-

tions indicated in the technical data.

We recommend using insulated circular section ues made of

stainless steel with smooth internal walls.

The ue cross-section should be constant for its whole

length (we recommend a minimum height of 3.5 - 4 m).

• We recommend tting a chamber at the base of the ue

to collect solid material and any condensate. Dilapidated

ues and ues made of unsuitable materials (asbestos,

galvanized steel, corrugated iron, etc.) with rough or

porous internal surfaces are illegal and detrimental to

stove operation.

• The ue should be used for one single stove only (it

cannot receive the outlet of other reboxes)

• For a good draught, the ue should be free from

obstructions, such as bottlenecks, horizontal sections and

sharp edges; any nonvertical sections should slope by not

more than 45° from the vertical (g. 3).

• If the ue to be used has previously been used for other

stoves or replaces, it must be carefully cleaned to prevent

faulty operation and avert the risk of unburnt deposits

on the internal ue walls catching re.

• In normal working conditions, the ue must be cleaned

at least once a year.

• For optimal operation, the ue draught must create a

pressure drop between 0.12 and 0.2 mbars. Lower values

may lead to unpleasant smoke emissions when loading

the stove and produce excessive soot deposits; higher

values would lead to excessively fast combustion and a

decrease in thermal efciency. To fall within the correct

values, refer to the UNI Standard 10683 table.

• If there are several ues on the roof, the others should

be at least 2 metres away and the stove chimney pot

should be at least 40 cm higher than the others.

Please refer to the chapter of the UNI 10683 regulation

regarding positioning of chimney pots.

• We recommend installing a re damper on the smoke

duct.

SMOKE DUCT

The smoke duct connects the smoke outlet to the ue inlet.

The smoke duct must be made with steel or ceramic rigid

pipes.

Flexible metal pipes or bre-cement pipes are not allowed.

Horizontal and counterslope sections should be avoided.

Any cross-secion change should be made in correspondence of

the stove outlet and not at the ue inlet.

Angles greater than 45° are not allowed (see gures 1,2,3,4).

The connection between the smoke duct and the steel ue

should be sealed with high temperature resistant mastic.

CHIMNEY POT

The chimney pot must have a wind guard (for any clarication,

please refer to your retailer), an internal section

equivalent to that of the ue, and smoke outlet cross-section

at least twice that of the internal ue cross-section.

For correct operation, please refer to UNI 10683.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Demy Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Demy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info