Bedienungsanleitung Edilkamin Demy (Seite 15 von 28) (Englisch)

810764

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

- 15 -

ENGLISH

INSTRUCTIONS FOR USE

A further suggestion:

To light the re the rst time, always use small pieces of wood.

They burn more quickly and thus bring the replace to the cor-

rect temperature more quickly.

Use larger pieces of wood to refuel the re.

Always place the wood well back in the replace, almost in

contact with the back wall of the same, so that even it if slips it

will not touch the door.

First lighting

The replace paintwork is subject to the so-called ageing phe-

nomenon until the normal working temperature is reached for

the rst time.

This may give rise to an unpleasant smell.

In this case, air the room where the replace is installed ad-

equately.

The phenomenon will disappear after the rst few times the

replace has been lit.

Lighting a cold replace

To light the stove use small blocks of wood (20-25 cm in

length, making up an amount of about 3 kg), positioned verti-

cally at the back of the rebox.

Push the control above the top completely in (see Fig. 2 page

38).

Lighting can be performed in the following manner:

- MANUAL LIGHTING = lighting the wood with a relighter

and closing the door

- AUTOMATIC LIGHTING = using the remote control and

pressing key “A” for 2 seconds starts the pellet lighting-phase,

which allows wood burning.

Light the wood using a relighter and close the door. As soon

as the ames have died down and a good bed of embers has

been formed, load the rebox with a normal amount of wood

(do not exceed the maximum amount specied in the table on

Page 32).

If the re is too intense we recommend partially closing the pri-

mary air valve (in manual mode) using the appropriate control

(see Illustr. 2 see Page 38) positioned parallel to the bottom of

the rebox.

The stove will operate differently depending on the draw in the

chimney and adjustment of the combustion air valve.

During the initial operating period it may take a little while

to nd the correct adjustment of the combustion air valve to

obtain the best operation from the stove.

It should be noted that if an insufcient amount or excessively

large pieces of wood are used to light the stove the combustion

chamber will not reach the optimum operating temperature,

resulting in poor combustion and the formation of an excessive

amount of smoke.

NOTE:

do not use alcohol, petrol, kerosene or other liquid fuels to light

the re.

Keep liquid fuels away from the re.

Do not use relighters made from petroleum or chemical sub

stances: they may cause serious damage to the rebox walls.

Use eco-friendly relighters only.

Overloading (over 3,1 kg/h) or excessively lively ames may

damage the rebox compartment.

ATTENTION:

If the hearth is fuelled by an excessive amount of fuel or an

improper fuel, the danger of overheating can occur with conse-

quent damage to the product.

Adding fuel when the replace is hot

Open the door and place the desired quantity of wood onto the

existing embers (without exceeding the quantity limits given in

the technical table).

The wood will heat up with the consequent expulsion of the

humidity content in the form of steam. This will lower the

temperature inside the replace which must be compensated

quickly with a sufcient input of combustion air.

Functioning in mild weather

To suck in air for combustion and to release the fumes, the

replace needs the draught created by the ue.

As the outdoor temperature increases, so the strength of the

draught decreases. If it is warmer than 10°C outside, check the

ue draught before lighting the re.

If the draught is weak, rst light the re in “start-up” mode us-

ing small pieces of fuel.

Once a correct draught has been reached, normal sized fuel can

be introduced.

Adding fuel

To add more wood, it is advisable to use a protective glove.

Open the door slowly.

This will avoid the formation of air eddies which can cause the

smoke to puff out into the room.

When is the right moment to add wood? When the fuel has

been burnt almost to embers.

Removing the ash (only when the stove is out and cold)

Remove the ash with a dustpan or a vacuum cleaner.

Place the ash only in non-combustible containers; remember that

remaining embers can re-light even 24 hours after burning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Edilkamin Demy Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Edilkamin Demy

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info