Bedienungsanleitung Edilkamin Logo (Seite 29 von 146) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

810792

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

- 29 -

ENGLISH

INSTRUCTIONS FOR USE

Loading the feed screw.

Should the pellet hopper empty completely the feed screw

must be Ŏ lled. To do so, keep the + and – keys pressed simul-

taneously for a few seconds (on the remote control or synoptic

panel). Once released, ‘REFILL’ will appear on the display.

This must be carried out before ignition if the stove has stopped

due to the pellets having Ŏ nished.

It is quite normal for some pellet residue to remain inside the

hopper, this is what the feed screw is unable to pick up.

Once a month, fully vacuum the hopper to prevent dusty resi-

due from accumulating.

Automatic ignition

With the stove on standby, press the 0/1 button for 2 seconds

(on the synoptic panel or remote control). This will startup

the ignition process, ‘Start’ will appear on the display and a

countdown will commence in seconds (1020). There is no

preset time for the ignition process: its duration will be automa-

tically shortened if the control board detects that certain tests

have been carried out positively. The ŏ ame appears after about

5 minutes.

Manual ignition

At a temperature lower than 3 °C – too low for the electrical

resistance to become red hot - or if the resistance is temporarily

not working, you can use a Ŏ relighter to ignite the stove.

Insert a well-lit Ŏ relighter into the combustion chamber, close

the door and press 0/1 on the synoptic panel or remote control.

Operating modes

Manual: the user sets the desired operating power (from

a minimum of 1 to a maximum of 5)

Automatic: the user sets the temperature desired in the

room. The stove reads this and adjusts the power to reach

the set temperature. Once this is reached, it sets itself to

power 1.

Manual mode from synoptic panel/remote control

(optional)

With the stove in operation mode or on standby, press and

release the MENU button on the synoptic panel/remote

control and ‘Power’ will appear on the display (showing

the power at which the stove is working). Rotate the left

knob or press the + key on the remote control to increase

the operating power (from Power 1 to Power 5).

Setting the fan via the Synoptic Panel

With the stove in operation mode or on standby, rotate the

right knob to adjust the ventilation setting (from 1 to 10 in

all powers).

Automatic mode from synoptic panel/remote control

(optional)

Press the MENU button twice to switch from manual to

automatic mode and adjust the temperature desired for the

room (use the right knob on the panel or the + and – keys

on the remote control to set the temperature between 10

and 29 ...., and the stove will regulate the operating power

required to reach it.

If the set temperature is lower than the room temperature,

the stove works at Power 1.

Shutdown

For greater comfort, the stove and the air vents go off

at the same power at which it was operating.

With the stove in operation mode press the 0/1 key for 2

seconds (on the synoptic panel or remote control). The

shutdown procedure will begin and the countdown is

displayed. This varies according to the power at which it

is running when the shutdown phase begins.

The shutdown phase (which will extinguish the ŏ ame

without leaving any unburnt material in the combustion

chamber and cool the stove), consists of:

• Pellet loading ceases.

• Ventilation is activated at the level at which the stove

was operating.

• Smoke expulsion motor enabled.

Never unplug the stove during the shutdown process.

Setting the clock

Press the MENU button for 2 seconds and use the + and –

keys to follow the instructions given on the display to

access the ‘Clock’ menu. This allows you to set the time on the

electronic control board.

Then press MENU and the following data appears in

sequence – this can be adjusted:

day, month, year, hour, minutes, day of the week.

When ‘Save?’ appears on the display you can check that

the settings have been entered correctly before conŎ rming.

Press MENU to save the information (‘Save OK’ then

appears on the display).

Weekly timer

Press the MENU button on the remote control for 2

seconds to access the time setting function and press the

+ key to access the weekly timer function – ‘Program ON/

OFF’ will appear on the display.

A maximum of three timer programs can be set for each

day of the week.

As you conŎ rm via the MENU button, one of the following

options will appear:

- ‘No Prog.’ (no program is set).

- ‘Daily program’ (a single program is set for every day)

- ‘Weekly program’ (a program is set for each day of the

week).

Move from one to the other using the + and – keys.

Use the MENU button to conŎ rm the ‘Daily program’

option and access the selection of the number of programs

(ignition/shutdown) to be set per day. Use the ‘Daily program’

option to set the identical program/s for every day

of the week.

The following will be displayed if the + key is pressed:

- No Programs.

- 1st daily program (one ignition and one shutdown per

day), 2nd daily program (same as before), 3rd daily program

(same as before).

Use the MENU button to show them in reverse order.

If the 1st program is selected, the ignition time is shown.

The display shows: 1 Ignition Hour 10.30; use the +/–

keys to change the hour and press MENU to conŎ rm.

The display shows: 1 Ignition Minutes 10.30; use the +/–

keys to change the minutes and press MENU to conŎ rm.

Edilkamin Logo Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info