Bedienungsanleitung Einhell BT-CD 24-1 i (Seite 18 von 96) (Englisch, Dänisch, Schwedisch, Norwegisch)

606191

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

- 18 -

5. Before starting the equipment

Be sure to read the following information before

you put the cordless screwdriver into operation:

1. Charge the battery only with the charging unit

supplied.

2. Only ever use sharp drill bits and screwdriver

bits which are suitable for the purpose and in

faultless condition.

3. Always check for concealed electric cables

and gas and water pipes when drilling and

screwing in walls.

Additional handle (Fig. 1 /Item 13)

The additional handle (13) enables you to achieve

better stability whilst using the equipment.

The additional handle (13) is secured to the

housing by a clamp. It can be screwed to the right

or left side.

6. Operation

6.1 Charging the battery (Fig. 2-3)

1. Remove the battery pack (5) from the handle

(Fig. 2) by pressing the pushlock buttons (8)

on the left and right side of the battery pack

(5).

2. Check that your mains voltage is the same as

that marked on the rating plate. Plug the char-

ging cable (7) of the charging unit (6) into the

power socket. The green LED on the charging

unit then comes on.

3. Insert the battery pack (5) into the battery

charger (6). The red LED will come on to in-

dicate that the battery pack is being charged.

Charging has ﬁ nished when the red LED

goes out and the green LED comes on again.

The battery pack may become a little warm

during the charging process. This is normal.

Caution! At temperatures of 45°C and higher the

battery cannot be charged. In this case remove

the battery from the charger, let it cool down and

then recharge it.

If the battery pack fails to charge, check for the

following:

•

Voltage at the power socket

•

Good contact at the charging contacts of the

charging unit

If the battery pack still fails to charge, send

•

the charging unit

•

and the battery pack

to our customer service center.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly.

You must recharge the battery pack when you

notice that the power of the cordless equipment

drops. Never fully discharge the battery pack. This

will cause it to develop a defect!

6.2 Torque setting (Fig. 4 / Item 1)

The cordless hammer drill/screwdriver is ﬁ tted

with a mechanical torque selector.

The torque for a particular screw size is set with

the setting ring (1). The torque is dependent on a

number of factors:

•

On the type and hardness of the material in-

volved

•

On the type and length of the screws used

•

On the requirements that the screw connec-

tion has to satisfy

The grating disengagement of the coupling in-

dicates that the selected torque level has been

reached.

Caution! Only ever adjust the setting ring

when the equipment is at a standstill.

6.3 Drilling/hammer drilling (Fig. 4)

•

For drilling purpose, adjust the torque setting

(1) to the setting “Drill”.

•

For hammer drilling purpose, adjust the

torque setting (1) to the setting “Hammer”.

In the drill and hammer drill settings the slip cou-

pling is non-functional. The maximum torque is

available for drilling and hammer drilling.

6.4 Changeover switch (Fig. 5/Item 3)

The slide switch above the On/Oﬀ switch is for

setting the direction of rotation of the cordless

screwdriver and for preventing the cordless

screwdriver from being switched on inadvertently.

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to

the gearing, the direction of rotation must only be

changed when the screwdriver is at a standstill.

When the slide switch is in the middle position,

the On/Oﬀ switch is blocked.

Anl_BT_CD_24_1_i_SPK1.indb 18Anl_BT_CD_24_1_i_SPK1.indb 18 04.09.12 09:4304.09.12 09:43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell BT-CD 24-1 i Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell BT-CD 24-1 i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info