Bedienungsanleitung Einhell BT-CD 24-1 i (Seite 19 von 96) (Englisch, Dänisch, Schwedisch, Norwegisch)

606191

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

- 19 -

6.5 On/Oﬀ switch (Fig. 5/Item 4)

Inﬁ nitely variable speed control is possible with

the On/Oﬀ switch. The further you push the

switch, the higher the speed of the cordless

screwdriver.

6.6 Changing the bit (Fig. 6)

Caution! Set the changeover switch (3) to its

center position whenever you carry out any work

(for example changing the tool, maintenance

work, etc.) on the cordless hammer drill/screwdri-

ver.

•

Open the chuck (2).

•

The chuck opening (a) must be large enough

to hold the tool (drill bit or screwdriver bit).

•

Select the suitable tool. Push the tool as far

as possible into the chuck opening (a).

•

Tighten the chuck (2) and then check that the

tool is secure.

6.7 Screwing

It is advisable to use self-centering screws (e.g.

Torx, cross recessed head) as these will enable

you to work safely and reliably. Always make sure

that the bit used is of the same size and shape as

the screw. Set the torque to suit the screw size as

speciﬁ ed in the instructions.

6.8 Magnetic screw holder (Fig. 4/Item 9)

Screws can be placed on the magnetic screw hol-

der for easy reach during operation.

6.9 Selector switch for 1st/2nd gear

(Fig. 4 / Item 10)

You can work with a higher or lower speed de-

pending on the position of the selector switch.

Change the gear only when the drill is at a stand-

still. If you fail to observe this point, the gearing

may be damaged.

6.10 Battery capacity indicator

(Fig. 2/Item 11)

Press the button for the battery capacity indicator

(12). The LCD display of the battery capacity indi-

cator (11) shows the charge status of the battery

using 5 bars.

All bars are shown:

The battery is fully charged.

2 to 4 bars are shown:

The battery has an adequate remaining charge.

One bar is shown:

The battery is empty, recharge the battery.

7. Cleaning, maintenance and

ordering of spare parts

Always pull out the mains power plug before star-

ting any cleaning work.

7.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device

immediately each time you have finished

using it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The

ingress of water into an electric tool increases

the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which

require additional maintenance.

7.3 Ordering replacement parts:

Please quote the following data when ordering

replacement parts:

•

Type of machine

•

Article number of the machine

•

Identification number of the machine

•

Replacement part number of the part required

For our latest prices and information please go to

www.isc-gmbh.info

Anl_BT_CD_24_1_i_SPK1.indb 19Anl_BT_CD_24_1_i_SPK1.indb 19 04.09.12 09:4304.09.12 09:43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell BT-CD 24-1 i Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell BT-CD 24-1 i

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info