Bedienungsanleitung Einhell GE-BC 43 AS (Seite 25 von 112) (Englisch, Dänisch, Schwedisch, Norwegisch)

605943

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

- 25 -

6. Before starting

Each time before use, check the following:

•

That there are no leaks in the fuel system.

•

That the equipment is in perfect condition and

that the safety devices and cutting devices

are complete.

•

That all screws are securely fastened.

•

That all moving parts move smoothly.

6.1 Fuel and oil

Recommended fuels

Use only a mixture of unleaded petrol and special

2-stroke engine oil. Mix the fuel mixture as indica-

ted in the fuel mixing table.

Important: Do not use a fuel mixture which has

been stored for longer than 90 days. Important:

Never use 2-stroke oil with a recommended mi-

xing ratio of 100:1. The manufacturer’s warranty

will be voided in case of engine damage due to

inadequate lubrication. Important: Only use con-

tainers designed and approved for the purpose to

transport and store fuel.

Pour the correct quantities of petrol and 2-stroke

oil into the mixing bottle (see scale printed on the

bottle). Then shake the bottle well.

6.2 Fuel mixing table

Mixing procedure: 40 parts petrol to 1 part oil

Petrol 2-stroke oil

1 liter 25 ml

5 liters 125 ml

7. Operation

Please note that the statutory regulations gover-

ning noise abatement may diﬀ er from one loca-

tion to another.

Before starting up the equipment remove the pro-

tective caps from the cutting blade.

7.1 Starting with a cold engine

Fill the tank with the required amount of oil/petrol

mix. See „Fuel and oil“.

1. Set the equipment down on a hard, level sur-

face.

2. Press the fuel pump (primer) (Fig. 2/Item 29)

10 times.

3. Move the On/Oﬀ switch (Fig. 2/Item 9) to „I“.

4. Set the choke lever (Fig. 2/Item 17) to I I.

5. Actuate the decompression lever (Fig. 42/

Item 33).

6. Hold the equipment ﬁ rmly and pull out the

starter cable (Fig. 2/Item 14) until you feel it

begin to resist. Then tug sharply on the starter

cable 2 times.

7. Set the choke lever (Fig. 2/Item 17) to I

8. Hold the equipment ﬁ rmly and pull out the

starter cable (Fig. 2/Item 14) until you feel it

begin to resist. Then tug sharply on the starter

cable 4 times. The equipment should start.

Important: Never allow the starter line to snap

back. This may result in damage.

Once the engine has started, allow the equip-

ment to warm up for 10 seconds.

Important: Since the choke lever is secured,

the cutting tool starts to operate when the

engine is started.

Then release the choke lever by actuating the

throttle lever once.

9. If the engine does not start up, repeat steps

4-9 above.

Please note: If the engine does not start up even

after several attempts, read the section „Engine

troubleshooting“.

Please note: Always pull the starter cord out in

a straight line. If it is pulled out at an angle, then

friction will occur on the eyelet. As a result of this

friction, the cable will become frayed and will

wear away faster. Always hold the starter handle

when the cable retracts.

Never allow the cable to snap back when it has

been pulled out.

7.2 Starting with a warm engine

(The equipment has been idle for less than 15-20

min.)

1. Set the equipment down on a hard, level sur-

face.

2. Switch the On/Of switch to „I“.

3. Actuate the decompression lever (Fig. 42/

Item 33).

4. Hold the equipment ﬁ rmly and pull out the

starter cable until you feel it start to resist.

Then tug sharply on the starter cable. The

equipment should start after 1-2 tugs. If the

equipment does not start after 6 pulls, repeat

steps 1 – 9 of the procedure for starting the

engine from cold.

Anl_GE_BC_43_AS_SPK1.indb 25Anl_GE_BC_43_AS_SPK1.indb 25 09.10.13 17:4109.10.13 17:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-BC 43 AS Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell GE-BC 43 AS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info