Bedienungsanleitung Einhell GE-BC 43 AS (Seite 26 von 112) (Englisch, Dänisch, Schwedisch, Norwegisch)

605943

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

- 26 -

7.3 Switching oﬀ the engine

Emergency Stop procedure:

If it becomes necessary to stop the equipment im-

mediately, set the On/Oﬀ switch to „Stop“ or „0“.

Normal procedure:

Let go of the throttle lever and wait until the engi-

ne has changed to idling speed. Then set the On/

Oﬀ switch to „Stop“ or „0“.

7.4 Using the harness

Important! Always use the harness when

working with the equipment. Always switch oﬀ

the equipment before you release the harness.

(Otherwise there is a risk of injury.)

•

Fit the harness (25) as shown in Fig. 22.

•

Hook the equipment to the harness (Fig. 23).

•

Adjust to the perfect working and cutting po-

sition using the various harness adjusters on

the harness (Fig. 23).

•

To establish the optimum length of the har-

ness, you should then make a few swinging

movements without starting the engine (Fig.

25).

The harness is ﬁ tted with a quick-release mecha-

nism. Pull the red part of the harness (Fig. 24) if

you need to remove the equipment quickly.

7.5 Work practice

Practice all the work steps with the engine swit-

ched oﬀ before you start to use the equipment.

8. Working with the petrol power

scythe

Extending the cutting line

Caution! Do not use any kind of metal wire or

metal wire encased in plastic in the line spool.

This may cause serious injuries to the user.

To extend the cutting line, run the engine at full

speed and tap the line spool on the ground. This

will automatically extend the line. The blade on

the safety shield will cut the line to the appropriate

length (Fig. 26).

Important: Remove all grass and weed remnants

at regular intervals to prevent the shaft tube over-

heating. Lawn, grass and weed remnants become

trapped under the safety shield (Fig. 27) and

prevent the shaft tube from receiving adequate

ventilation. Remove the remnants carefully using

a screwdriver or the like.

Diﬀ erent cutting methods

When the equipment is correctly assembled it

will cut weeds and long grass in places which are

diﬃ cult to access, e.g. along fences, walls and

foundations and also around trees. It can also

be used for „mowing“ down vegetation so that a

garden can be better prepared or a certain area

cleared down to the soil.

Please note: Even if it is used carefully, cutting

around foundations, stone or concrete walls, etc.

will result in the line suﬀ ering more than normal

wear.

Trimming/mowing

Swing the trimmer from side to side in a scything

motion. Always keep the line spool parallel to the

ground. Check the site and decide which cutting

height you require. Guide and hold the line spool

at the required height to obtain an even cut (Fig.

28).

Low trimming

Hold the trimmer right in front of you at a slight

angle so that the underside of the line spool is

above the ground and the line strikes the correct

target. Always cut away from yourself. Never draw

the trimmer towards yourself.

Cutting along fences/foundations

Approach wire mesh fences, lath fences, natural

stone walls and foundations slowly so that you

can cut close to them without striking the obstac-

le with the line. If, for example, the line strikes

stones, stone walls or foundations, it will wear or

fray.

If the line strikes wire fencing, it will break.

Trimming around trees

When trimming around tree trunks, approach

slowly so that the line does not strike the bark.

Walk around the tree, cutting from left to right. Ap-

proach grass or weeds with the tip of the line and

tilt the line spool forwards slightly. Warning! Take

extreme care during mowing work. When doing

such work keep a distance of 30 meters between

yourself and other people or animals.

Anl_GE_BC_43_AS_SPK1.indb 26Anl_GE_BC_43_AS_SPK1.indb 26 09.10.13 17:4109.10.13 17:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-BC 43 AS Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell GE-BC 43 AS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info