Bedienungsanleitung Einhell GE-BC 43 AS (Seite 28 von 112) (Englisch, Dänisch, Schwedisch, Norwegisch)

605943

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

- 28 -

9.3 Maintenance of the air ﬁ lter (Fig. 31-33)

Soiled air ﬁ lters reduce the engine power by

supplying too little air to the carburetor. Regular

checks are therefore essential. The air ﬁ lter (T)

should be checked after every 25 hours of use

and cleaned if necessary. If the air contains a

lot of dust, the air ﬁ lter should be checked more

frequently.

1. Remove the air ﬁ lter cover (Fig. 31-32).

2. Remove the air ﬁ lter (Fig. 33).

3. Clean the air ﬁ lter by tapping it or blowing it

out.

4. Assemble in reverse order.

Important: Never clean the air ﬁ lter with petrol or

inﬂ ammable solvents.

9.4 Maintenance of the spark plug (Fig. 34)

Spark plug sparking gap = 0.6mm. Tighten the

spark plug with a torque of 12 to 15 Nm. Check

the spark plug for dirt and grime after 10 hours of

operation and if necessary clean it with a copper

wire brush. Thereafter service the spark plug after

every 50 hours of operation.

1. Pull out the spark boot plug (Fig. 13).

2. Remove the spark plug (Fig. 34) with the sup-

plied multifunction tool (27).

3. Assemble in reverse order.

9.5 Carburetor settings

Important! Settings on the carburetor may only

be made by authorized customer service person-

nel.

9.6 Setting the idling speed

Important! Set the idling speed when the equip-

ment is warm.

If the engine stalls when the throttle is not pressed

and you have ruled out all the other possible

causes listed in section 12 „Troubleshooting“, the

idling speed must be adjusted. To do this, turn

the idling speed screw (Fig. 41/Item E) clockwise

until the equipment runs smoothly at idling speed.

If the idling speed is so fast that the cutting tool

turns as well, it has to be reduced by turning the

idling speed screw for as long as is required for

the cutting tool to stop turning as well.

9.7 Applying grease to the gear unit

After every 20 hours of use add a little gear gre-

ase (approx. 10 g.) at the lubrication nipple (Fig.

28/Item 21).

10. Cleaning, storage, transport and

ordering of spare parts

10.1 Cleaning

•

Clean the equipment as required with a damp

cloth and, if necessary, mild washing up

liquid.

Important!

Always pull out the spark boot plug each time

before carrying out any cleaning. Never immerse

the equipment in water or other liquids in order to

clean it.

Store the equipment in a safe and dry place out of

the reach of children.

10.2 Storage

Important: Never put the equipment into storage

for longer than 30 days without carrying out the

following steps.

Storing the equipment

If you intend to store the equipment for longer

than 30 days, the equipment must be prepared

accordingly. Otherwise the fuel still remaining in

the carburetor will evaporate and leave a rubbery

sediment. This can cause problems when starting

up the equipment and may require expensive

repairs.

1. Slowly remove the fuel tank cap to release

any pressure that may have formed in the

tank. Carefully empty the tank.

2. To remove the fuel from the carburetor, start

the engine and let it run until it stops.

3. Leave the engine to cool (approx. 5 minutes).

4. Remove the spark plug (see section 9.4).

5. Add one teaspoon of 2-stroke engine oil into

the combustion chamber. Slowly pull the star-

ter cord several times to apply a layer of oil

to all internal components. Fit the spark plug

again.

Note: Store the equipment in a dry place and

far away from possible ignition sources such as

an oven, a gas-ﬁ red hot water boiler, a gas-ﬁ red

dryer, etc.

Anl_GE_BC_43_AS_SPK1.indb 28Anl_GE_BC_43_AS_SPK1.indb 28 09.10.13 17:4109.10.13 17:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-BC 43 AS Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell GE-BC 43 AS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info