Bedienungsanleitung Einhell GE-HC 18 Li T Kit (Seite 25 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

605964

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

- 25 -

Filling the oil tank (Fig. 11):

•

Place the chainsaw on a flat surface.

•

Clean the area around the oil tank cover (Item

31) and then clean the oil tank cover.

•

Fill the tank (Item 30) with saw chain oil. In

the process, make sure that no dirt enters

the tank, as this could cause the oil nozzle to

become blocked.

•

Close the oil tank cover (Item 31).

After the chain saw mounting kit has been ﬁ tted

and when the equipment is not being used, slip

the cutter guard (Fig. 1/Item 18) over the moun-

ted cutter bar with saw chain in order to prevent

injuries.

5.3 Adjusting the additional handle

(Fig. 12-13)

(a) Setting the tilt of the additional handle

Open (a) the lock (F). Set the desired tilt of the

additional handle (9). Close (b) the lock (F).

b) Shifting the additional handle

Open (a) the lock (H) and slide the additional

handle (9) into the required position. Close (b) the

lock (H).

5.4 Using the shoulder strap

Warning! Always use the shoulder strap when

working with the equipment. Switch oﬀ the equip-

ment before you take oﬀ the shoulder strap (risk

of injury).

1. Hook the carabiner (Fig. 4/Item A) into the

strap holder.

2. Slip the shoulder strap (Fig. 14/Item 8) over

your shoulder.

3. Adjust the length of the shoulder strap so that

the strap attachment is at waist level (Fig. 14).

4. The shoulder strap is equipped with a buckle.

Press the hooks together (Fig. 15) if you need

to put down the equipment quickly.

5. To change the strap position on the equip-

ment, press together the two metal loops (Fig.

4/Item L / M) and adjust the strap attachment

on the tube.

5.5. Adjusting the angle of the handle

(Fig. 16)

Press the two safety lock-oﬀ s (5) and adjust the

angle of the handle (2) to any of 4 latching posi-

tions.

5.6. Adjusting the angle of the motor housing

(Fig. 17)

Press the two safety lock-oﬀ s (14) and adjust the

angle of the motor housing (13a) to any of 7 lat-

ching positions.

5.7 Adjusting the telescopic tube (Fig. 18)

1. Undo the telescopic tube lock nuts (10 + 12)

by turning them counter-clockwise.

2. Pull out the telescopic tubes (11 + 13) to suit

the required working height.

3. Secure the telescopic tube lock nuts (10 +

12) by them turning clockwise.

5.8 Fitting the chain saw mounting kit to the

motor head (Fig. 19 – 20)

The cutter guard must be slipped over the moun-

ted cutter bar with saw chain in order to prevent

injuries.

1. Position the chain saw mounting kit and the

motor head such that the arrows on both

parts coincide.

2. Press the chain saw mounting kit against the

motor head. This will cause the lock button

(R) to be pushed to the right. Turn the chain

saw mounting kit clockwise. The chain saw

mounting kit will lock onto the motor head and

is then secured in place. This will cause the

lock button (R) to be pushed to the left.

5.9 Turning the chain saw mounting kit

through 90° on the motor head (Fig. 21)

The cutter guard must be slipped over the moun-

ted cutter bar with saw chain in order to prevent

injuries.

1. Pull the lock button (R) to the right.

2. Turn the chain saw mounting kit 90° counter-

clockwise. The chain saw mounting kit will

lock onto the motor head and is then secured

in place.

5.10 Removing the chain saw mounting kit

from the motor head (Fig. 19 – 20)

The cutter guard must be slipped over the moun-

ted cutter bar with saw chain in order to prevent

injuries.

1. Pull the lock button (R) to the right.

2. Turn the chain saw mounting kit to the point

where the arrows on the motor head and

chain saw mounting kit coincide, allowing the

mounting kit to be removed.

Anl_GE_LC_18_Li_T_SPK7.indb 25Anl_GE_LC_18_Li_T_SPK7.indb 25 11.08.14 13:0811.08.14 13:08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-HC 18 Li T Kit Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info