Bedienungsanleitung Einhell GE-HC 18 Li T Kit (Seite 27 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

605964

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

- 27 -

Hearing protection and protective goggles.

Wear a protective helmet with integral face and

hearing protection. This will oﬀ er protection

against falling branches and any branches if they

spring back.

Safe working

•

To ensure that you can work in safety you

must use the equipment at a working angle of

max. 60°.

•

Never stand under the branch you want to

saw.

•

Use special caution when working with bran-

ches under tension and splintered wood.

•

Possible risk of injury caused by falling bran-

ches and catapulting pieces of wood.

•

When the equipment is in operation keep

other persons and animals away from the

danger zone.

•

The equipment is not protected from electric

shock through contact with high-voltage

cables. Keep a minimum distance of 10 m

from live cables. Electric shock can cause

fatal injury.

•

When working on slopes always stand to the

upper or left or right side of the branch you

wish to cut.

•

Hold the equipment as close as possible to

your body. This will help you to keep your ba-

lance.

Cutting techniques

•

When removing branches, hold the equip-

ment at an angle of max. 60° to the horizontal

to avoid being hit by a falling branch (Fig. 27).

•

Start with the bottom branches on the tree.

This will make it easier for the cut branches to

drop.

•

After completing a cut, the weight of the saw

will abruptly increase for the operator as the

saw is no longer supported by the branch.

This can result in you losing control over the

saw.

•

Remove the saw from the cut only with the

saw chain still running. This will prevent the

saw from getting jammed.

•

Never cut with the tip of the saw.

•

Never cut into the bulging branch collar. This

will prevent the tree from healing.

Sawing oﬀ smaller branches (Fig. 25):

Place the contact surface of the saw onto the

branch. This will prevent the saw from making

jerky movements when you begin a cut. Exerting

slight pressure, guide the saw from the top to the

bottom through the branch.

Sawing oﬀ larger and longer branches

(Fig. 26):

Carry out a relief cut when working on larger

branches.

Start by sawing through 1/3 of the branch diame-

ter (a) from the bottom to the top with the top side

of the cutter rail. Then saw towards the ﬁ rst cut (b)

from the top to the bottom with the bottom side of

the cutter rail.

Saw oﬀ longer branches in several steps to keep

control over the impact location.

Kick-back!

The term “kickback” describes what happens

when the running chainsaw suddenly kicks up-

ward and backward. Usually, this is caused by

contact between the tip of the cutter rail and the

workpiece or the saw chain becoming trapped.

In the event of kickback, large forces occur sud-

denly and violently. As a result, the chainsaw

usually reacts uncontrollably. This can often result

in very serious injuries to the worker or persons in

the vicinity. The risk of kickback is at its greatest

when the saw is positioned for a cut in the region

of the tip of the cutter rail, as the leverage eﬀ ect is

greatest there. It is therefore safest to position the

saw as ﬂ at as possible.

Important!

•

Make sure that the chain tension is always

correctly adjusted.

•

Only use a chainsaw if it is in perfect working

order.

•

Only work with a saw chain that has been

properly sharpened in accordance with the

instructions.

•

Never cut with the upper edge or the tip of the

cutter rail.

•

Always hold the chainsaw firmly with both

hands.

Cutting wood which is under tension

Special care is required when cutting wood which

is under tension. Wood which is under tension

from which it is released by cutting may in some

cases react completely unpredictably and un-

controllably. In the worst case this could result in

extremely severe or even fatal injuries. This type

of work must only be performed by persons who

have been specially trained.

Anl_GE_LC_18_Li_T_SPK7.indb 27Anl_GE_LC_18_Li_T_SPK7.indb 27 11.08.14 13:0811.08.14 13:08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-HC 18 Li T Kit Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info