Bedienungsanleitung Einhell GE-TM 102 BS (Seite 26 von 52) (Deutsch, Englisch, Französisch)

605745

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

- 26 -

Replacing the light bulb (Fig. 50)

Open the engine hood. To change the light bulb

(18 W), twist the connector (Item m) counter-

clockwise.

6.1 Mowing

Only use a sharp blade that is in good condition.

This will prevent the grass blades from fraying

and the lawn from turning yellow.

Try to steer in straight lines for a nice, clean look.

The swaths should overlap each other by a few

centimeters in order to avoid stripes. For optimum

mowing results we would recommend that you

plan your path with left-hand turns only.

Keep the underside of the mower housing clean

and remove grass build-up. Deposits not only

make it more diﬃ cult to start the mower; they

decrease the quality of the cut and make it harder

for the equipment to bag the grass. Always mow

along inclines (not up and down). You can prevent

the lawn mower from slipping down by holding a

position at an angle upwards. Select the cutting

height according to the length of the grass. If ne-

cessary, mow a number of times so that you never

cut more than 4cm of grass in one go.

Switch oﬀ the engine and pull out the ignition key

and spark boot plugs before doing any checks on

the blade. Keep in mind that the blade continues

to rotate for a few seconds after switching oﬀ . Ne-

ver attempt to manually stop the blade. Regularly

check to see if the blade is securely attached,

is in good condition and is sharp. If the contrary

is the case, have the blade sharpened or repla-

ced. In the event that the blade strikes an object,

immediately switch oﬀ the lawn mower and wait

for the blade to come to a complete stop. Then

inspect the condition of the blade and the blade

mount. Replace any parts that are damaged.

Starting mowing

Important. Be sure to observe the safety ins-

tructions.

1. Start the engine. Important: Observe all the

information on operation contained in this ma-

nual.

Note: For detailed information on starting the

engine, refer to the enclosed manual from Briggs

& Stratton.

Important.

If you actuate the ignition key again while the

engine is running, you will damage the starting

system.

2. Place the speed lever in the “Hare” position.

3. Set the mower unit to the highest possible

position.

4. Start the mower unit.

5. Release the locking brake. Slowly actuate the

drive lever (forward). Adjust the cutting height

and driving speed to the grass you are going

to mow.

Note:

•

For optimum mowing results with thick, high

grass, use a low speed.

•

Switch off the mower unit whenever you re-

verse.

•

Switch off the mower unit and set it to the

highest position before crossing over any

obstacles.

Level indicator for the grass basket

The grass basket is supplied with a sensor which

emits a signal tone to tell you when the grass bas-

ket is full. Switch oﬀ the mower unit whenever the

signal sounds (Section 6 Mower unit switch). Do

not let the grass basket get too full as it will clog

the ejector chute.

Adjusting the grass basket ﬁ ll level sensor (Fig.

41) If the signal sounds when the grass basket

is not full yet, shorten the length. If the signal

sounds too late and the grass basket is too full,

extend the length.

6.2 Emptying the grass basket (Fig. 38)

Important. Never open the grass basket when

the mower unit is running.

1. Apply the locking brake.

2. Pull the release lever for the grass basket

(Item 2) up and out of the holder.

3. The grass basket can now be emptied with

ease.

4. Close the grass basket. Ensure that the grass

basket is fully closed again.

5. Slide the release lever back into the holder

again.

6. Resume mowing, having regard for the safety

instructions as you do so.

Cleaning the ejector chute

The ejector chute can become clogged if you

mow wet grass or if you drive too fast when mo-

wing (Fig. 25/Item 18). Please follow these inst-

ructions in order to remove a blockage:

1. Disengage the drive unit for the attachments,

apply the locking brake, switch oﬀ the engine

and pull out the spark boot plug and the igniti-

on key.

Anl_GE_TM_102_BS_SPK7.indb 26Anl_GE_TM_102_BS_SPK7.indb 26 21.01.15 08:4821.01.15 08:48

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GE-TM 102 BS Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info