Bedienungsanleitung Einhell GH-BC 30 AS (Seite 24 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

605959

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

- 24 -

Trimming/mowing

Swing the trimmer from side to side in a scything

motion. Always keep the line spool parallel to the

ground. Check the site and decide which cutting

height you require. Guide and hold the line spool

at the required height to obtain an even cut (Fig.

28).

Low trimming

Hold the trimmer right in front of you at a slight

angle so that the underside of the line spool is

above the ground and the line strikes the correct

target. Always cut away from yourself. Never draw

the trimmer towards yourself.

Cutting along fences/foundations

Approach wire mesh fences, lath fences, natural

stone walls and foundations slowly so that you

can cut close to them without striking the obstac-

le with the line. If, for example, the line strikes

stones, stone walls or foundations, it will wear or

fray.

If the line strikes wire fencing, it will break.

Trimming around trees

When trimming around tree trunks, approach

slowly so that the line does not strike the bark.

Walk around the tree, cutting from left to right. Ap-

proach grass or weeds with the tip of the line and

tilt the line spool forwards slightly. Warning! Take

extreme care during mowing work. When doing

such work keep a distance of 30 meters between

yourself and other people or animals.

Mowing

When mowing, you want to cut all the vegetation

down to the ground. To do this, set the line spool

at an angle of 30° to the right. Place the handle in

the required position. Remember the increased

risk of injury to the user, watchers and animals,

and the danger of damaging property due to ob-

jects (for example stones) being thrown up (Fig.

29).

Warning! Do not use the equipment to remove

objects from footpaths, etc. The equipment is a

powerful tool and can throw small stones and

other objects a distance of 15 meters or more,

causing injuries and damage to cars, houses and

windows.

Sawing

The equipment is not suitable for sawing.

Jamming

If the cutting blade jams as a result of attempting

to cut vegetation that is too dense, switch oﬀ the

engine immediately. Remove the grass and scrub

from the equipment before you restart it.

Preventing recoil

When you work with the blade, there is a risk of

recoil if it strikes solid objects such as tree trunks,

branches, tree stumps, stones or the like. This will

throw the equipment backwards in the direction

opposite to the rotation of the tool. This can cause

you to lose control of the equipment. Do not use

the blade near fences, metal posts, boundary

stones or foundations. For cutting dense stalks,

position the blade as shown in Fig. 30 to prevent

recoil.

9. Maintenance

Always switch oﬀ the equipment and pull out the

spark boot plug before carrying out any mainte-

nance work.

9.1 Replacing the line spool/cutting line

1. Dismantle the line spool (13) as described in

section 5.1.6. Press the spool together (Fig.

12a) and remove one half of the housing (Fig.

12b).

2. Take the line spool out of the line spool

housing (Fig. 12c).

3. Remove any remaining cutting line.

4. Place the new cutting line in the center and

attach the resulting loop to the recess in the

spool splitter (Fig. 12d).

5. Wind the line on to the spool counter-clockwi-

se with tension. The spool splitter will separa-

te the two halves of the nylon line (Fig. 12e).

6. Hook the last 15 cm of the two ends of the

line to the line holders opposite the line spool

(Fig. 12f).

7. Thread the two ends of the line through the

metal eyelets in the line spool housing (Fig.

12c).

8. Press the line spool into the line spool

housing.

9. Pull the two line ends brieﬂ y and powerfully to

release them from the line holders in the line

spool.

10. Cut the excess line to a length of around 13

cm. This will reduce the load on the engine

when starting up and warming up.

11. Fit the line spool again. See section 5.1.6. If

Anl_GH_BC_30_AS_SPK7.indb 24Anl_GH_BC_30_AS_SPK7.indb 24 16.06.14 11:4216.06.14 11:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GH-BC 30 AS Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info