Bedienungsanleitung Einhell GH-BC 30 AS (Seite 25 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

605959

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

- 25 -

you are replacing the complete line spool,

ignore points 3-6.

9.2 Grinding the safety hood blade

The safety hood blade can become blunt over

time. When you notice this, undo the screw hol-

ding the safety hood blade on the safety hood.

Clamp the blade in a vise. Sharpen the blade with

a ﬂ at ﬁ le and make sure that the angle of the cut-

ting edge is not altered in the process. File in one

direction only.

9.3 Maintenance of the air ﬁ lter

Soiled air ﬁ lters reduce the engine output by sup-

ply too little air to the carburetor. Regular checks

are therefore essential. The air ﬁ lter should be

checked after every 25 hours of use and cleaned

if necessary. If the air contains a lot of dust, the air

ﬁ lter should be checked more frequently.

1. Remove the air ﬁ lter cover (Fig. 10a).

2. Remove the ﬁ lter element (Fig. 10b/10c).

3. Clean the ﬁ lter element by tapping it or

blowing it.

4. Assemble in reverse order.

Important: Never clean the air ﬁ lter with petrol or

inﬂ ammable solvents.

9.4 Maintenance of the spark plug

Spark plug sparking gap = 0.6mm. Tighten the

spark plug with a torque of 12 to 15 Nm. Check

the spark plug for dirt and grime after 10 hours of

operation and if necessary clean it with a copper

wire brush. Thereafter service the spark plug after

every 50 hours of operation.

1. Dismantle the protective cap (Fig. 10c/Item

21) using a screwdriver.

2. Pull oﬀ the spark plug boot (Fig. 11a) using

the pull hook (31).

3. Remove the spark plug (Fig. 11b) with the

supplied spark plug wrench (27).

4. Assemble in reverse order.

9.5 Carburetor settings

Important. Settings on the carburetor may only be

made by authorized customer service personnel.

The air ﬁ lter cover must be removed before any

work on the carburetor, as shown in Figures 10a

and 10b.

Setting the throttle cable:

If the maximum speed of the machine falls over

time and you have ruled out all the other causes

listed in section 12 Troubleshooting, it may be ne-

cessary to adjust the throttle cable.

First of all check whether the carburetor opens

fully when the throttle handle is pressed fully. This

is the case if the carburetor slide F rests against

the stop (Fig. 13a) when the throttle is fully open.

Figure 13a shows the correct setting. If the car-

buretor slide does not touch the stop, it must be

adjusted.

The following steps are required to adjust the

throttle cable:

•

Undo the lock nut (Fig. 13b/Item C) a few

turns.

•

Undo the adjusting screw (Fig. 13b/Item D)

until the carburetor slide F rests against the

stop when the throttle is fully open, as shown

in Fig 13.

•

Retighten the lock nut.

9.6 Setting the idling speed

Important. Set the idling speed when the equip-

ment is warm.

If the engine stalls when the throttle is not

pressed and you have ruled out all the other cau-

ses listed in section 11 Troubleshooting, the idling

speed must be adjusted. To do this turn the idling

speed screw (Fig. 13b/Item E) clockwise until the

equipment runs smoothly at idling speed. If the

idling speed is so fast that the cutting tool turns

as well, it has to be reduced by turning the idling

speed screw for as long as is required for the cut-

ting tool to stop turning as well.

9.7 Applying grease to the gear unit

After every 20 hours of use add a little gear gre-

ase (approx. 10 g.) at the lubrication nipple (Fig.

28/Item 21).

10. Cleaning, storage, transport and

ordering of spare parts

10.1 Cleaning

•

Keep the handles free of oil so that you can

maintain a firm grip.

•

Clean the equipment as required with a damp

cloth and, if necessary, mild washing up

liquid.

Important!

Always pull out the spark boot plug each time

before carrying out any cleaning. Never immerse

the equipment in water or other liquids in order to

clean it.

Store the equipment in a safe and dry place out of

the reach of children.

Anl_GH_BC_30_AS_SPK7.indb 25Anl_GH_BC_30_AS_SPK7.indb 25 16.06.14 11:4216.06.14 11:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell GH-BC 30 AS Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info