Bedienungsanleitung Einhell LE 30 (Seite 16 von 100) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

723951

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

- 16 -

4. Fan speed

To choose between a high and a low fan

speed, press the “Fan speed” switch (Fig. 2 /

Item 26).

5. Desired humidity

To adjust the desired humidity setting within

the range of 40% to 80% in 5% increments,

press the “Humidity setting” switch (Fig. 2 /

Item 25) and then press the “Higher/lower”

button (Fig. 2 / Item 24). If the prevailing hu-

midity at the integrated sensor falls below the

desired humidity setting by approx. 2%, the

compressor will stop, followed a little later by

the fan. If the prevailing humidity at the inte-

grated sensor exceeds the desired humidity

setting by approx. 2%, both the fan and the

compressor (3 minute restart inhibit function)

will start up again.

6. Timer

To set the desired operating time (1 – 24

hours) in 1 hour increments, press the switch

for “Timer settings” (Fig. 2 / Item 23) with the

device switched on and then press the “High-

er/lower” button (Fig. 2 / Item 24). If the timer

has not been switched on, the device will run

continuously. If the device is connected to the

voltage supply, press the switch for “Timer

settings” and then press the “Higher/lower”

button (Fig. 2 / Item 24) to set the time, in 1

hour increments, until the device is switched

on (1 – 24 hours).

7. To switch oﬀ , press the On/Oﬀ switch (Fig. 2 /

Item 21).

7. Emptying the condensate

collector

Note:

•

The device switches off automatically when

the condensate collector (Fig. 1 / Item 1) is

full. The „Condensate collector full“ LED will

light up and a warning signal will sound for a

few seconds.

•

If the condensate collector (Fig. 1 / Item 1) is

not refitted correctly after it has been emp-

tied, the “Condensate collector full” LED will

continue to shine.

•

Never remove the “Float” (Fig. 3 / Item A) from

the condensate collector, otherwise the auto-

matic switch-off function will no longer work.

•

If the condensate collector is dirty, you can

clean it with warm water.

1. Remove the condensate collector (Fig. 1 /

Item 1) by pulling it out carefully and then em-

pty it.

2. Slide the collector back into the device after

you have emptied it.

8. Using an external condensate

drain (Fig. 4)

Note:

•

Important: To prevent water damage, make

sure that the condensate is drained away pro-

perly at all times.

•

Important: If the weather is very cold you will

have to take appropriate measures to prevent

the water from freezing in the drainage hose.

•

It is best to direct the condensate into a lower

lying drain. If you use an external collecting

container (e.g. a trough), the equipment must

be positioned accordingly higher.

•

The drainage hose must be installed with a

downward gradient. It must not be kinked or

become clogged.

•

If the drainage hose becomes clogged, the

condensate must run into the condensate

collector from the overflow.

1. Remove the rubber plug and keep it in a safe

place (it must be reinserted in the connection

socket when the external condensate drain is

no longer used).

2. Connect the suction port (B) with a matching

water hose (C) with a 10 mm inside diameter.

De-icing function

To prevent the cooling elements becoming iced

up at operating temperatures below 21°C, the

equipment has a de-icing function. In this case

the compressor is switched oﬀ but the fan motor

continues to run.

During this phase the dehumidifying function is

interrupted for a few minutes.

Please observe the equipment’s operating range

(see Technical Data).

The equipment has a compressor protector which

automatically shuts down the equipment when

the temperature rises above 35°C or falls below

5°C, or when the power consumption rises too

high.

Anl_LE_16_20_30_SPK7.indb 16Anl_LE_16_20_30_SPK7.indb 16 24.02.16 08:3324.02.16 08:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell LE 30 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info