Bedienungsanleitung Einhell RT-SD 3.6-2 Li (Seite 19 von 100) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

782358

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

- 19 -

the charging cable is connected to the charging

adapter.

The red LED on the battery capacity indicator (5)

indicates that the battery is being charged. When

the charging has ﬁ nished, the red LED will go out

and the green LED will begin to shine.

Important. The handle may become a little warm

during the charging process. This is normal.

If the battery fails to charge, please check

• whether there is voltage at the socket outlet

• whether there is good contact at the charging

contacts of the charging unit

If the battery still fails to charge, send

• the charging unit

• and the screwdriver

to our customer service center.

Timely recharging of the battery will help it serve

you well for a long time. You must recharge the

battery when you notice that the power of the

cordless screwdriver drops.

6.2 Changeover switch (Fig. 3/Item 10)

The slide switch above the On/Oﬀ switch is for

setting the direction of rotation of the cordless

screwdriver and for preventing the cordless

screwdriver from being switched on inadvertently.

You can select between clockwise and counter-

clockwise rotation. Change the direction of rota-

tion only when the equipment is at a standstill.

If you fail to observe this point, the gearing may

become damaged. When the slide switch is in the

middle position, the On/Oﬀ switch is blocked.

6.3 On/Oﬀ switch (Fig. 3 / Item 9)

Press the On/Oﬀ switch to switch the cordless

screwdriver on. Release the On/Oﬀ switch again

to switch it oﬀ .

6.4 LED lamp (Fig. 3/Item 2)

The LED lamp (2) can be used to additionally illu-

minate the area where you want to drill or screw.

The LED lamp (2) will be lit automatically as soon

as you press the On/Oﬀ switch (9).

6.5 Angle setting (Fig. 3+4/Item 7)

The screwdriver can be locked into 2 diﬀ erent

angle settings. To do so, press and hold the lo-

cking button (7) and move the screwdriver into the

desired position. Then release the locking button

(7) again.

Important. Before you switch on the screwdriver,

make sure that it is correctly locked in the angle

position in question.

6.6 Battery capacity indicator (Fig. 5/Item 5)

Remove the cordless screwdriver from the char-

ging unit/charging station.

Press the button for the battery capacity indicator

(6). The battery capacity indicator (5) indicates

the charge state of the battery on 3 colored LEDs.

All the LEDs are lit:

The battery is fully charged.

The yellow and red LEDs are lit:

The battery has an adequate remaining charge.

Red LED:

The battery is empty, recharge the battery.

6.7 Torque setting (Fig. 5 / Item 3)

The torque for a particular screw size is set with

the setting ring (3). The torque is dependent on a

number of factors:

• On the type and hardness of the material

involved

• On the type and length of the screws used

• On the requirements that the screw connec-

tion has to satisfy

The grating disengagement of the coupling in-

dicates that the selected torque level has been

reached.

Important. Only ever adjust the setting ring

when the equipment is at a standstill.

6.8 Magnetic screw holder (Fig. 5/Item 4)

Screws can be placed on the magnetic screw hol-

der for easy reach during operation.

6.9 Changing the bit (Fig. 6)

Important. Set the changeover switch to its center

position whenever you carry out any work (for

example changing the bit, maintenance , etc.) on

the cordless screwdriver.

• Pull back and hold the locking sleeve (13).

• Insert the bit (a) in the bit chuck (1) and let go

of the locking sleeve (13).

• Check that the bit is locked in placed by

pulling on it.

Anl_RT_SD_3_6_1_Li_SPK1.indb 19Anl_RT_SD_3_6_1_Li_SPK1.indb 19 20.11.13 08:3420.11.13 08:34

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell RT-SD 3.6-2 Li Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell RT-SD 3.6-2 Li

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info