Bedienungsanleitung Einhell TH-RO 1100 E (Seite 23 von 112) (Englisch, Dänisch, Schwedisch, Norwegisch)

606717

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

- 23 -

6. Operation

•

Never use a low quality or damaged cutter.

Use only cutting tools with a shaft diameter of

6 mm or 8 mm. The cutters must also be desi-

gned for the appropriate idling speed.

•

Secure the workpiece so that it cannot be

thrown through the air as you work on it. Use

clamps or a vise.

•

Always guide the power cable away from the

back of the tool.

•

Never cut over metal parts, screws, nails etc.

6.1 ON/OFF switch (Fig. 12/Item 4)

Press the safety lock-oﬀ (5) and then press the

ON/OFF switch (4) to switch on the machine.

Release the ON/OFF switch (4) to switch oﬀ the

machine.

6.2 Speed control (Fig. 13 – Item 11)

The best speed depends on the material and the

diameter of the cutter. Select a speed between

11,000 and 30,000 rpm using the speed control

switch (11). You can choose from 7 diﬀ erent

switch positions. The speeds in the various switch

positions are as follows:

Switch position 1: approx. 11,000 rpm

(minimum speed)

Switch position 2: approx. 12,000 rpm

Switch position 3: approx. 15,000 rpm

Switch position 4: approx. 18,000 rpm

Switch position 5: approx. 22,000 rpm

Switch position 6: approx. 26,000 rpm

Switch position 7: approx. 30,000 rpm

(maximum speed)

To increase the speed:

Move the speed control switch (11) in the plus

direction.

To reduce the speed:

Move the speed control switch (11) in the minus

direction.

6.3 Adjusting the routing depth (Fig. 14 – 17)

•

Place the machine on the workpiece.

•

Undo the wing screw (16) and fixing handle

(9).

•

Slowly move the machine downwards until

the cutter makes contact with the workpiece.

•

Tighten the fixing handle (9).

•

Set the fine adjuster (15) to 0 as shown in Fig.

17.

•

Adjust the revolver end stop (14) so that the

depth stop (19) is above the end stop (a) set

to the lowest height.

•

Lower the depth stop (19) until it touches the

end stop (a). Then tighten the wing screw

(16).

•

Set the pointer (17) to the zero point on the

scale (18).

•

Undo the wing screw (16). Push the depth

stop (19) upwards until the pointer (17) points

at the required cutting depth on the scale

(18). Tighten the wing screw again.

•

Test the setting by completing a test cut on a

waste piece.

•

Now you can carry out the final adjustment

of the cutting depth. To do this turn the fine

adjuster (15) to the required dimension.

Turn the ﬁ ne adjuster (15) counter-clockwise: gre-

ater cutting depth

Turn the ﬁ ne adjuster (15) clockwise: lower cutting

depth

Turning the ﬁ ne adjuster (15) through one division

corresponds to a change of cutting depth of 0.04

mm, one whole turn corresponds to 1 mm.

On the precision adjustment device (15) you

can also turn the lower ring (b) separately. This

lets you reach the zero point without altering the

precision adjustment device (15). See Fig. 17 and

proceed as follows:

•

Press down the ring (b).

•

Hold and turn it until you have reached the

desired position.

•

Release the ring again.

Anl_TH_RO_1100_E_SPK1.indb 23Anl_TH_RO_1100_E_SPK1.indb 23 29.06.12 10:4629.06.12 10:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell TH-RO 1100 E Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell TH-RO 1100 E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info