Bedienungsanleitung Einhell TH-RO 1100 E (Seite 24 von 112) (Englisch, Dänisch, Schwedisch, Norwegisch)

606717

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

- 24 -

6.4 Routing

•

To avoid damage to the router, make sure

there are no foreign objects attached to the

workpiece.

•

Connect the mains plug to a suitable socket.

•

Hold the tool using both of its handles (7).

•

Place the router on the workpiece.

•

Set the cutting depth as described in point

6.3.

•

Select the speed as described in point 6.2

and switch the machine on (see point 6.1).

•

Test the machine settings using a piece of

waste.

•

Operate the tool at full speed. Only then

should you lower the router to its working

height and lock the machine with the locking

grip (9).

Cutting direction: The cutting tool turns clock-

wise. To avoid accidents you must always cut

against the direction in which the tool turns (Fig.

18).

Feed speed: It is very important to machine

the workpiece at the correct feed speed. We

recommend that before you machine the actual

workpiece, you carry out several trial cuts on a

waste piece of the same type. This will enable you

to ﬁ nd the best working speed for the workpiece

very easily.

Feed speed too low:

The cutter could heat up excessively. If you are

cutting inﬂ ammable material such as wood, the

workpiece could ignite.

Feed speed too high:

The cutter could be damaged. Cutting quality:

Rough and uneven.

Allow the cutter to come to a complete standstill

before removing the workpiece or putting down

the router.

6.5 Routing in stages

Depending on the hardness of the material you

wish to cut and the cutting depth, it may be a

good idea to proceed in stages.

•

If you wish to route in several stages, turn the

end stop revolver (14) after you have set the

cutting depth as described in point 6.3 so that

the depth stop (19) is over the highest end

stop (a).

•

Now route in this setting. After completing the

first routing operation, adjust the end stop

revolver (14) so that the depth stop (19) is

above middle end stop (a). Now complete a

routing operation in this setting as well.

•

Now set the lowest end stop (a) and finish the

routing.

6.6 Routing circles with the compass point

(13)

Proceed as follows to route circles around a cen-

tre point:

•

Fit and adjust the compass point (13) as de-

scribed in point 5.4.

•

Place the compass point (13) on the centre

point of the circle you wish to route and apply

pressure to it.

•

Complete the routing operation as described

in point 6.4.

6.7 Routing with the parallel stop (21)

Proceed as follows to route along a straight outer

edge of a workpiece:

•

Fit the parallel stop (21) as described in point

5.3.

•

Guide the parallel stop (21) along the outer

edge of the workpiece.

•

Complete the routing operation as described

in point 6.4.

6.8 Free-hand routing

The router can also be operated without any

guide rods. You can use it for freehand routing for

creative work such as the production of logos.

•

Use a very flat cutter setting for this purpose.

•

Check the direction in which the cutter is tur-

ning as you machine the workpiece (Fig. 18).

6.9 Shape and edge cutting (Fig. 19)

•

Special cutters with a guide ring may be used

for cutting shapes (a) and edges (b).

•

Fit the cutter.

•

Carefully guide the machine on to the workpi-

ece.

•

Guide the guide journal or ball bearing (c)

along the workpiece with gentle pressure.

 Important:

For deep cuts, carry out the work in several

steps according to the material in question.

Hold the router in two hands when carrying

out all cutting work.

Anl_TH_RO_1100_E_SPK1.indb 24Anl_TH_RO_1100_E_SPK1.indb 24 29.06.12 10:4629.06.12 10:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Einhell TH-RO 1100 E Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Einhell TH-RO 1100 E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info