Bedienungsanleitung EK63-EdilKamin DORE160 H (Seite 11 von 28) (Englisch)

810941

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

INSTALLATION

NOTA

Il diametro dell’uscita fumi non è il diametro del sistema camino. Il sistema camino deve essere

dimensionato secondo le norme nazionali e locali.

In particolare, (elenco non esaustivo) fare riferimento a EN 13384, EN 1443, EN 1856, EN 1457 e a

tutte le norme locali.

FLUE SYSTEM

(

Fumes duct, ﬂ ue and chimney pot

)

This chapter has been drawn up pursuant to

European regulations EN 13384, EN 1443, EN 1856

and EN 1457. The installer must observe both these

and any other local regulations. This manual does

not in any way substitute such regulations.

The product must be connected to a ﬂ ue system which

ensures that the fumes produced by combustion are

exhausted in complete safety.

Before positioning the appliance, the installer must

check that the ﬂ ue is suitable.

FUMES DUCT, FLUE

The fumes duct

(which connects the hearth's fumes

outlet with the ﬂ ue)

outlet with the ﬂ ue) and the ﬂ ue itself must, among

other regulatory requirements:

• receive the fumes from a single product (the

outlets of multiple appliances may not be

conveyed into a single ﬂ ue)

• be routed vertically for the most part

• have no downwards sloping sections

• preferably have a circular internal cross section,

or with a ratio of the sides of less than 1.5

• terminate at roof level with a proper chimney pot:

the ﬂ ue may not discharge directly on the wall

or into an enclosed space, even if the space in

question is open to the sky

• be made of material rated ﬁ re reaction class

A1 per UNI EN 13501 or analogous national

regulations

• be certiﬁ ed, with a chimney plate if metal

• be of uniform cross section or vary in cross

section only immediately after the outlet, not at

some mid point of its length

THE FUMES DUCT

Further to the general prescriptions for the fumes

duct and ﬂ ue, the fumes duct

• may not be made of ﬂ exible metal material

• must be insulated, if routed through unheated

areas or outdoors

• must not be routed through rooms where the

installation of combustion heat generators is

prohibited, there is risk of ﬁ re, or which cannot

be inspected

• must enable the recovery of soot and be open for

inspection

• have at most 3 bends with a maximum angle of

90°

• must have a single horizontal section with a

length of no more than 3 metres, depending on

the draw. Note, in any case, that long sections

promote the accumulation of dirt and are harder

to keep clean.

TYPICAL CASES

A: insulated steel ﬂ ue, pursuant to EN 1856

B: minimum height 1.5 m and, nevertheless, above the

level of the roof guttering

C-E: external ambient air intake (through section of at

least 80 cm²)

D: steel ﬂ ue inside existing masonry chimney

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

EK63-EdilKamin DORE160 H Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von EK63-EdilKamin DORE160 H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info