Bedienungsanleitung Elac SUB 2060D (Seite 35 von 48) (Deutsch, Englisch)

561007

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Description and use of the control panel

Page 31

Comment:

If you have obtained a remote control with your subwoofer, you have the option of

calling up two different, pre-settings. These differ in the parameterization of the

EQ1.

The preset “Audio” has been preset so that music is reproduced ‘neutrally’.

Therefore the “EQ 1 Level” is set to “OdB” and hence practically without function.

In contrast, the preset “Video” results in the EQ 1 in frequencies of around 59 Hz

being emphasized. This frequency range is particularly important for reproducing sound effects of films, and by

emphasizing this frequency you can experience your DVDs etc. with an overpowering fundamental, and a thrilling

quality.

The settings of other parameters of the subwoofer you have made remain unchanged, even after the pre-setting

has been switched. However, any settings for the EQ 1 are lost by a preset selection. If you have used the EQ 1 to

suppress other room resonances or to stress a frequency range, we recommend that you note the parameter val-

ues of the EQ 1, so that you can reset them when required.

8 EQ 2 Room resonance filter (only available with the model SUB 2080 D)

In comparison to the EQ 1, the EQ 2 is characterized by the narrow bandwidth of

the filter. Furthermore, this filter allows supports a reduction of a frequency range

by up to -12dB. The EQ 2 is thus highly suitable for specifically suppressing room

resonances and thus avoiding unwanted peaks in the frequency range. We

recommend the same procedure as for EQ 1when searching for possible room

resonances and setting the parameters.

To set the mean frequency of the filter, go to the rotation menu with one of the outer arrow keys to select “EQ 2

Frequency”. By pressing the selector key in the middle, you arrive frequency selection. Now select the required

frequency with one of the outer arrow keys, and return to the rotation menu by pressing the selector key. Your se-

lected frequency will now be shown.

To set the attenuation/amplification of the filter, go to the rotation menu with one of the outer arrow keys to select

“EQ 2 Level”. By pressing the selector key in the middle you arrive at the attenuation selection. Now select the re-

quired attenuation/amplification with one of the outer arrow keys, and return to the rotation menu by pressing the

selector key. Your selected attenuation/ amplification will now be shown.

9 Overview display

The overview display enables you to view all parameters and their present values

without going through the rotation menu.

To go to the overview display, go to the rotation menu with one of the outer arrow keys to the start screen. By

pressing the selector key in the middle, you reach the overview display. Pressing the selector key again returns

you to the start screen in the rotation menu.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elac SUB 2060D Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info