753497
13
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
13
ENGLISH
For machine performance see "Techni-
cal Specifications".
Any other use is not as specified and
prohibited.
The manufacturer is not liable for any
damage caused by unspecified use.
3.1 Powerbox
(welding power source)
3.2 SDV (separate wire feed
unit)
3.3 SWK (separate water-
cooling unit)
The SWK is automatically controlled by
the Powerbox.
Note:
Instructions on how to connect
and operate the SWK are given in the
separate instructions supplied with the
device.
3.4 Control unit
3. Operating Elements
1Connection (front) for earth
cable (- Pole).
2Main switch
switches the Powerbox and all
devices connected to it ON or OFF.
3Power supply outlet for addi-
tional devices
Rating: 10 A / 230 V.
4Bracket with chain
secures the gas cylinder against
turning over.
5Pilot lead
for SDV.
1
2
3
4
5
98
6
7
6Power cable
SDV motor. When using a SWK the
power supply cable is connected to
the SWK. The SDV then automati-
cally controls the water cooling
when welding.
7Welding cable
with cable connector (+ pole).
8Connection (rear) for earth cable
(- pole).
9Power supply cable
with CEE plug.
10 Euro connector socket for weld-
ing gun
for connection of all commercially
available welding guns.
11 Connection for coolant runback
from welding gun.
12 Connection for coolant feed to
welding gun.
13 Connector socket for pilot lead
of external devices.
14 Control unit.
Selection, display and setting of the
operating parameters.
The control unit for the machine’s
default settings is located inside the
SDV.
A
V
10
11
12
13
14
15
16
17
18
20
19
21
15 Connection for shielding gas
line
16 Connector socket for exteral
programming
17 Connector socket for power sup-
ply
18 Connector plug for welding cur-
rent supply
19 Connection for coolant runback
into SWK.
20 Connection for coolant feed from
SWK.
21 Connector socket for pilot lead
22 Parameter selection (momen-
tary contact switch)
for selection of the parameter to be
displayed and/or adjusted.
The LEDs [23-26] indicate the
selected parameter.
23 LED wire feed [m/min]
24 LED welding current [A]
A
V
27
26
25
24
23
28
22
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Elektra Beckum Mig Mag 232EP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info