Bedienungsanleitung Elica Bridge (Seite 10 von 16) (Englisch)

471175

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Instruction on mounting and use

Consult the designs in the front pages referenced in the text

by alphabet letters. Closely follow the instructions set out

in this manual. All responsibility, for any eventual

inconveniences, damages or fires caused by not complying

with the instructions in this manual, is declined.

Use

The hood is designed to be utilized either for suction version

at external evacuation or filtering version at internal

recirculation.

Ducting version

The hood is equipped with a top air outlet B for discharge of

fumes to the outside (exhaust pipe and pipe fixing clamps not

provided).

Filter version

Should it not be possible to discharge cooking fumes and

vapour to the outside, the hood can be used in the filter

version, fitting an activated carbon filter and the deflector F

on the support (bracket) G, fumes and vapours are recycled

through the top grille H by means of an exhaust pipe

connected to the top air outlet B and the connection ring

mounted on the deflector F (exhaust pipe and pipe fixing

clamps not provided).

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

(not supplied).

Installation

The minimum distance between the supporting surface for the

cooking vessels on the hob and the lowest part of the range

hood must be not less than 50cm from electric cookers and

65cm from gas or mixed cookers.If the instructions for

installation for the gas hob specify a greater distance, this

must be adhered to.

Electrical connection

The electrical tension must correspond to the tension noted

on the label placed inside the cooker hood. Connect the

electrical plug, where provided, to the an easily accessible

outlet in conformity with local standards in force. Where an

electrical plug is not provided (for direct connection to

electrical network) place a standards approved bipolar switch

with an aperture distance of not less than 3mm (accessible)

from the contacts.

Attention: substituting the supply cable must be carried out

by the authorised technical assistance service.

Mounting

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Preliminary information for installation of the hood:

Disconnect the hood during electrical connection, by turning

the home mains switch off.

Remove the fat/s filter/s and the carbon filter frame.

Do not tile, grout or silicone this appliance to the wall. Surface

mounting only. Do not fix chimney flue to furniture or fly over

shelves unless the chimney flue can be easily removed, in

case maintenance is ever required.

Assembling the chimney flue support/bracket (3 parts):

The three parts should be fixed with 4 screws, the support

extension is adjustable and should correspond to the internal

width of the telescopic chimney flue.

Assembling the deflector (only when a deflector

composed of 3 parts is supplied – the deflector should be

only for the filter version):

The three parts should be fixed with 2 screws, the deflector

extension is adjustable and should correspond to the width of

the chimney flue support, to which it is then fixed.

Only for the models illustrated in Fig. 1D/8D - 1E/8E -

1Q/8Q

Remove AND CONSERVE the screws that temporarily fix

the flue units (for reasons of transport), the hood or the

flue unit (on the basis of the model possessed) with the

suction unit. The two parts should be disassembled to

facilitate installation. Check how the parts are fixed together

to repeat assemblage at the opportune moment.

Before fixing the hood to the suction unit check that the metal

band (steam shield) that holds the lamp and the filter/s /

greases is well attached to the front. If necessary adjust the

position of the band forwards until the end stop.

Attention!

The chimney is predisposed for installation of the filter

Version.

In certain models where it is required to use the cooker hood

in the suction version then it is possible to overturn the upper

section of the chimney

and insert it inside the lower section of the chimney so that the

air-exit perforations are not visible. The chimneys in which

this operation is possible are recognizable by their bracket

fixing points G which are repeated also in the lower side of the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Bridge Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info