Bedienungsanleitung Elica Bridge (Seite 12 von 16) (Englisch)

471175

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Description of the hood

Fig. 1

1. Control panel

2. Grease filter

3. Grease filter release handle

4. Halogen lamp

5. Vapour screen

6. Telescopic chimney

7. Air outlet (used for filter version only)

8. point lighting (only for the model in Fig. 1G)

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Functioning – Model with Keyboard

A. on/off light switch

B. on/off aspiration switch and minimum power selection

B+C. medium power selection aspiration switch

B+D. maximum power selection aspiration switch

b-c

b-c-d-e

a. ON/OFF lighting

b. OFF motors

c. - d. - e. Minimum suction power (c.), medium (d.),

maximum (e.).

f. Operation warning light (where present).

Note: Some models only possess one suction Power.

Attention: the models with an electric valve are supplied with 3

keys:

(a)Light ON/OFF, (b)Electric Valve Closure and (c)Opening.

Functioning - 5-key electronic model

123OOI

1234 567 8 9

1. Motor OFF button

2. ON button and motor speed selection button 1 - 2 - 3 - 1 -

2 - . . . .

3. Speed 1 LED

4. Speed 2 LED and metal grease filter saturation LED (in

this latter case, the LED will flash - See instructions on

grease filter cleaning).

Once the grease filters have been cleaned, press button

1 for about 3 seconds until you hear the acoustic signal

(beep): the LED 4 will now stop flashing.

5. Speed 3 LED and active carbon filter saturation LED (in

this latter case, the LED will flash - See instructions on

active carbon filter replacement).

Once you have replaced the charcoal filter, press button

1 for about 3 seconds until you hear the acoustic signal

(beep). LED 5 will now stop flashing.

Warning!

The active carbon filter saturation LED is not activated.

In order to activate the active carbon filter saturation

indicator, press buttons 2 and 7 simultaneously for 3

seconds. Initially, only LED 4 will flash, then after the 3

seconds have passed, LED 5 will also start flashing,

indicating that the active carbon filter saturation control

system is active.

To switch off the system, re-press the same two buttons:

after 3 seconds LED 5 will stop flashing and the device

will be switched off.

6. Intensive speed LED

7. Intensive speed ON switch

This speed should be used when the concentration of

cooking fumes or odours is particularly strong (for

example when frying, cooking fish etc.).

The fast speed will run for about 5 minutes and then

return to the speed previously set automatically (1, 2 or

3), or switch off if no speed was selected.

To turn off the fast speed, before the end of the 5

minutes, press button 1 or button 2.

8. OFF lamp button

9. ON lamp button

If the hood fails to operate correctly, briefly disconnect it from

the mains power supply for almost 5 sec. by pulling out the

plug. Then plug it in again and try once more before

contacting the Technical Assistance Service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Bridge Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info