Bedienungsanleitung Elica Ye (Seite 26 von 136) (Alle Sprachen)

649836

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

filter(s) when necessary to maintain a good grease filter

efficiency. Use the maximum diameter of the ducting system

indicated in this manual to optimize efficiency and minimize

noise.

Additional Installation Specifications:

Use only the fixing screws supplied with the product for

installation or, if not supplied, purchase the correct screws

type.

Use the correct length for the screws which are identified in

the Installation Guide.

In case of doubt, consult an authorised service assistance

centre or similar qualified person.

WARNING! Failure to install the screws or fixing device in

accordance with these instructions may result in electrical

hazards.

Use

The hood is conceived for the suction of cooking fumes and

steam and is destined only for domestic use.

The hood is designed to be used either for exhausting or filter

version.

Ducting version

In this case the fumes are conveyed outside of the building by

means of a special pipe connected with the connection ring

located on top of the hood.

Attention! The exhausting pipe is not supplied and must be

purchased apart.

Diameter of the exhausting pipe must be equal to that of the

connection ring.

In the horizontal runs the exhausting pipe must be slightly

slanted (about 10°) and directed upwards to vent the air easily

from the room to the outside.

Attention! If the hood is supplied with active charcoal filter,

then it must be removed.

Connect the hood and discharge holes on the walls with a

diameter equivalent to the air outlet (connection flange).

Using the tubes and discharge holes on walls with smaller

dimensions will cause a diminution of the suction performance

and a drastic increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensible length.

! Use a duct with as few elbows as possible (maximum

elbow angle: 90°).

! Avoid drastic changes in the duct cross-section.

! Use a duct as smooth as possible inside.

! The duct must be made of certified material.

Filter version

One active charcoal filter is needed for this and can be

obtained from your usual retailer.

The filter removes the grease and smells from the extracted

air before sending it back into the room through the upper

outlet grid.

Installation

Specialised personnel must carry out both the electrical

and the mechanical installation.

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the

range hood must be not less than 65cm from electric cookers

and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a

greater distance, this must be adhered to.

Electrical connection

The mains power supply must correspond to the rating

indicated on the plate situated inside the hood. If provided with

a plug connect the hood to a socket in compliance with current

regulations and positioned in an accessible area, after

installation. If it not fitted with a plug (direct mains connection)

or if the plug is not located in an accessible area, after

installation, apply a double pole switch in accordance with

standards which assures the complete disconnection of the

mains under conditions relating to over-current category III, in

accordance with installation instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

The hood is provided with a special power cable ; if the cable

is damaged, request a new one from Technical Service.

Mounting

The accessories for ceiling mounting are not provided as

ceilings of different materials require different types of fixing

accessories.

Use mounting systems suitable for the ceilings of the

premises and the weight of the equipment.

For more details and in case of doubt, in order to ensure

proper installation of the product, we recommend that you

contact a dealer and a specialized technician.

The chimney is a CRISTALPLANT ® product, it should be cut

to size (see also illustrative drawings).

The installation of the hood and the cut of the chimney must

be performed by a qualified technician using suitable cutting

systems.

For cutting, we recommend the use of the Widia tools, and

equipment (e.g., band saw or similar) capable of cutting

marble, wood and mineral materials.

If possible, we recommend that you perform a cut in the

excess part of the chimney to check the suitability of the tool.

Visit www.cristalplant.it for more details on the material and

manufacturer.

The warranty will not be effective in the case of cosmetic

defects or damages caused and/or arising from failure to

comply with the above provisions, as the assembly and the

cutting of the chimney are activities pertaining to and under

the full responsibility of a third party other than the

Manufacturer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elica Ye Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info