Bedienungsanleitung Elkron 80TC1L00133 (Seite 69 von 248) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

741458

Zoom out

Zoom in

Vorherige Seite

1/248

Nächste Seite

DS80TC1L-001 69

4.4.3 Focusing functions

The camera focus may be adjusted manually using the FOCUS +

and FOCUS – controls.

As the autofocus function is always on, a manual setting made using FOCUS + and FOCUS - will be kept only until a

pan, tilt or zoom command is used. In this case, autofocus will adjust focus automatically again.

Refer to the specific section for additional details on focusing and on the various options.

NOTE:

The autofocus function cannot work correctly in the following cases:

• The object to be focused on it not in the middle of the image

• There are far and near object in the frame

• Bright light is shining on the subject

• The subject is behind a glass pane covered in drops or dust.

• The subject is moving very quickly.

• The subject is not well lit.

• The subject is too big.

4.4.4 Iris opening functions

The iris opening may be controlled manually using the IRIS

and IRIS- commands.

The manual setting made using IRIS+

and IRIS- will be kept only until a pan, tilt or zoom command is used if the

automatic iris opening option is enabled (the default setting is on). In this case, the opening will be controlling

automatically again.

Refer to the specific section for additional details on iris opening adjustment.

4.4.5 Preset positions programming and recalling

The ELKDome camera can store up to 200 panning, tilting and zooming configurations (called preset positions) which

can be recalled at any time.

The manual focusing and iris opening settings cannot be stored.

NOTE:

When saving presets, remember that, from 51 to 63, from 78 to 101 and from 171 to 186, the presets are reserved and

cannot be saved or used to position the camera.

The following examples show how to program the free presets and recall them.

Example: programming preset number 32

1. Position the camera in a certain pan, tilt and zoom configuration.

2. Enter the command PRESET

+ 32 + ENTER

3. The setting is saved and the message “Stored” appears.

From this moment onwards, simply enter the command CALL

+ 32 + ENTER to move the camera to the preset

position.

NOTE: The saved value will be written over if the setting is reprogrammed.

The presettings are saved in a permanent memory area of the camera where they are maintained also when power is

disconnected. However, restoring default settings will delete all preset values.

Caution. The presettings store the coordinates according to an angular reference system. Therefore, the reference

system zero point may become misaligned with the camera mechanics after prolonged use of the tilting and panning

functions. Minor inaccuracies in preset positions may occur. In this case, calibrate the angular coordinate system using

the {DOME RESET} command. This calibration is automatically run when the camera is switched on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron 80TC1L00133 Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info