Bedienungsanleitung Elkron IR600FC-N (Seite 6 von 18) (Deutsch, Englisch, Französisch, Italienisch)

741401

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

6 DS80TC2S-001

ENGLISH

The IR600FC/N is a passive infrared motion sensor (PIR) with built-in camera. When motion is detect, it sends alarm signals and

high-quality images to the system control unit.

The detector has a detection range of 12 metres when it is mounted at 2 metres from the ground. The detector consists of two

parts, a cover and a base. The cover contains all the electronic and optical components and the camera, while the base is used for

fixing. The base has arrangements for holes for installation on a flat surface and holes for fixing to the corner bracket (included).

The detector is also provided with a single tamper switch which is activated when an attempt to open the cover or detach it from

the wall.

Part identification

1. Illuminator

The illuminator provides sufficient light to acquire images in poor lighting conditions.

The blue LED and the illuminator both blink once when the function button is pressed for 10 seconds to

indicate that the detector was reset.

2. Blue LED/Function button

Meaning of the LEDs:

The blue LED lights up in the following conditions:

- The blue LED blinks once every 20 minutes: the detector has lost the connection with the control

unit.

- The blue LED lights up for 30 seconds: the detector is being initialised in test mode.

- The blue LED blinks fast twice: the detector is connected correctly to the control unit.

- The blue LED lights up for two seconds during normal operation: the detector has detected a

motion.

- The blue LED blinks fast: the detector is transmitting images to the control unit.

- The blue LED and the illuminator blink once: the detector was reset.

Using the function button:

- Press the button once to send a supervision signal.

- To reset the detector: hold the button pressed for 10 seconds. Release the button when the

illuminator and the blue LED blink once.

- For the learning procedure of the detector on the control unit

3. IR sensor lens

The sensor is used to detect the movements of people and/or animals by detecting their body

temperature.

4. Camera

lens

5. Battery compartment lid

6. Tamper switch

The tamper switch is activated if the detector is detached from the wall or from the corner bracket

or if the cover is opened.

7. Battery compartment

8. Jumper JP3 PIR sensitivity

- Jumper on: "High" sensitivity level.

- Jumper off: "Normal" sensitivity level (default setting).

9. Jumper JP2

- Jumper On: after transmitting following a detected movement, the signals and the acquired

images will be transmitted if any other movements are detected (default setting).

- Jumper Off: the detector has a “sleep time” (see below) of approximately 1 minute to save

energy.

10. Fastening screw

Jumper On

The jumper is

connected between

the two pins.

Jumper Off

the jumper is removed

or "arranged" on a pin.

Jumper

The jumper is connected

between the two pins.

Jumper Off

the jumper is removed

or "arranged" on a pin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Elkron IR600FC-N Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Elkron IR600FC-N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info